background image

4. Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the 
FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a residential 
installation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications.  However, there is no guaran-
tee that interference will not occur in a particular installation.  If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct 
the interference by one of the following measures:

‡

Reorient or relocate the receiving antenna.

‡

Increase the separation between the equipment and receiver.

‡

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

‡

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void 
the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device 
may not cause harmful interference, and (2) this device must accept any interference received, including interference that 
may cause undesired operation.

.

18

Содержание EL-451R




















Отзывы: