background image

EOP-D73-001-7-002-05E 

E.J. OZONE PRODUCTS 

- 5 - 

To ensure your safety 

Please refer to “Marks and descriptions”, “Biological influences caused by Ozone”, “Dangerous 
characteristics for ozone treatment”, “Cautions on operating the analyzer”, and “Cautions on the 
low-pressure mercury lamp” shown below. 

 

Marks and descriptions 

Note 1:  Serious injury includes loss of sight, high-temperature/low-temperature burn, electric shock, 

bone fracture, and poisoning, and involves aftereffects or requires hospitalization or hospital 
visit for a long period of time for medical treatment. 

Note 2: Minor or moderate injury includes burn, electric shock, etc. that do not require 

hospitalization or hospital visit for a long period of time for medical treatment. Property 
damage is defined as extended damage resulting from loss of properties and damage to 
equipment.

 

 

Mark

 

Description

 

 

DANGER 

DANGER 

indicates an imminently hazardous situation which,   

if not avoided, will result in death or serious injury. 

 

WARNING 

WARNING 

indicates a potentially hazardous situation which,   

if not avoided, could result in death or serious injury.

 

 

CAUTION 

CAUTION 

indicates a potentially hazardous situation which,   

if not avoided, may result in minor or moderate injury.

 

 

DANGER 
ELECTRIC 
SHOCK

 

DANGER

 ELECTRIC SHOCK indicates places where electric 

shock may result unless sufficient caution is exercised.

 

 

CAUTION 
UV RAY

 

CAUTION

 UV RAY indicates places where your eyes and skin 

may be damaged unless sufficient caution is exercised.

 

 

CAUTION 

HIGH TEM- 
PERATURE 

CAUTION

 HIGH TEMPERATURE indicates places where burn, 

etc. may result unless sufficient caution is exercised.

 

 

 

Содержание ME800 series






























































































Отзывы: