background image

9. Radio-controlled night flying is limited to low perform-

ance model aircraft (less than 100 mph).

The model aircraft must be equipped with a lighting sys-

tem which clearly defines the aircraft’s attitude and di-

rection at all times.

10. The operator of a radio-controlled model aircraft

shall control it during the entire flight, maintaining

visual contact without enhancement other than by

corrective lenses that are prescribed for the pilot. No

model aircraft shall be equipped with devices which

allow it to be flown to a selected location which is be-

yond the visual range of the pilot.

PARK FLYER SAFE OPERATING RECOMMENDATIONS

-  Inspect your model before every flight to make

certain it is airworthy.

-  Be aware of any other radio frequency user who

may present an interference problem.

-  Always be courteous and respectful of other users

of your selected flight area.

-  Choose an area clear of obstacles and large

enough to safely accommodate your flying activity.

-  Make certain this area is clear of friends and

spectators prior to launching your aircraft.

-  Be aware of other activities in the vicinity of your

flight path that could cause potential conflict.

-  Carefully plan your flight path prior to launch.

-  Abide by any and all established AMA National

Model Aircraft Safety Code.

3

311

E-flite Stearman PT-17 15e ARF Assembly Manual

Instructions for Disposal of WEEE by

Users in the European Union

This product must not be disposed of with other waste.

Instead, it is the user’s responsibility to dispose of their

waste equipment by handing it over to a designated

collection point for the recycling of waste electrical

and electronic equipment. The separate collection

and recycling of your waste equipment at the time

of disposal will help to conserve natural resources

and ensure that it is recycled in a manner that protects

human health and the environment. For more

information about where you can drop off your waste

equipment for recycling, please contact your local city

office, your household waste disposal service or where

you purchased the product.

Содержание Stearman PT-17 15e ARF

































Отзывы: