background image

E-flite P-38/F-5E Lightning Assembly Manual

Damage Limits

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT 

OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR 

PRODUCTION OR COMMERCIAL LOSS IN ANY WAY 

CONNECTED WITH THE PRODUCT, WHETHER SUCH CLAIM IS 

BASED IN CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT 

LIABILITY. Further, in no event shall the liability of Horizon exceed 

the individual price of the Product on which liability is asserted. As 

Horizon has no control over use, setup, final assembly, modification 

or misuse, no liability shall be assumed nor accepted for any 

resulting damage or injury. By the act of use, setup or assembly, the 

user accepts all resulting liability.
If you as the Purchaser or user are not prepared to accept the 

liability associated with the use of this Product, you are advised to 

return this Product immediately in new and unused condition to the 

place of purchase.
Law: These Terms are governed by Illinois law (without regard to 

conflict of law principals).

Safety Precautions

This is a sophisticated hobby product and not a toy. It must be 

operated with caution and common sense and requires some basic 

mechanical ability. Failure to operate this Product in a safe and 

responsible manner could result in injury or damage to the Product 

or other property. This Product is not intended for use by children 

without direct adult supervision. The Product manual contains 

instructions for safety, operation and maintenance. It is essential to 

read and follow all the instructions and warnings in the manual, 

prior to assembly, setup or use, in order to operate correctly and 

avoid damage or injury.

Questions, Assistance, and Repairs

Your local hobby store and/or place of purchase cannot provide 

warranty support or repair. Once assembly, setup or use of the 

Product has been started, you must contact Horizon directly. This 

will enable Horizon to better answer your questions and service 

you in the event that you may need any assistance. For questions 

or assistance, please direct your email to productsupport@

horizonhobby.com, or call 877.504.0233 toll free to speak to a 

service technician.

Inspection or Repairs

If this Product needs to be inspected or repaired, please call for 

a Return Merchandise Authorization (RMA). Pack the Product 

securely using a shipping carton. Please note that original boxes 

may be included, but are not designed to withstand the rigors 

of shipping without additional protection. Ship via a carrier that 

provides tracking and insurance for lost or damaged parcels, as 

Horizon is not responsible for merchandise until it arrives and is 

accepted at our facility

. A Service Repair Request is available at 

www.horizonhobby.com on the “Support” tab. If you do not have 

internet access, please include a letter with your complete name, 

street address, email address and phone number where you can 

be reached during business days, your RMA number, a list of the 

included items, method of payment for any non-warranty expenses 

and a brief summary of the problem. Your original sales receipt 

must also be included for warranty consideration. Be sure your 

name, address, and RMA number are clearly written on the outside 

of the shipping carton.

Warranty Inspection and Repairs

To receive warranty service, you must include your original sales 

receipt

 verifying the proof-of-purchase date. Provided warranty 

conditions have been met, your Product will be repaired or 

replaced free of charge. Repair or replacement decisions are at the 

sole discretion of Horizon Hobby.

Содержание P-38 Lightning 400 ARF





































Отзывы: