E-FLITE Opterra, Инструкция по эксплуатации

Страница: 10 / 27

EN
10
Opterra
®
1.2M
Using the Video Transmitter
SPMVT1001 CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8
A Band A 5865 5845 5825 5805 5785 5765 5745 5725
B Band B 5733 5752 5771 5790 5809 5828 5847 5866
E Band E** 5705 5685 5665 5665 5885 5905 5905 5905
F FS/IRC 5740 5760 5780 5800 5820 5840 5860 5880
R RaceBand 5658 5695 5732 5769 5806 5843 5880 5917
Power level
LEDs (Green)
SPMVT1001* SPMVT1001EU
*†
L 25mW 25mW
2 200mW N/A
6 600mW N/A
SPMVT1001EU CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8
1. Band A 5865 5845 5825 5805 5785 5765 5745 5745
2. Band B 5733 5752 5771 5790 5809 5828 5847 5866
4. FS/IRC 5740 5760 5780 5800 5820 5840 5860 5860
5. RaceBand 5732 5732 5732 5769 5806 5843 5843 5843
* HAM license required for use in North America, not for use in Europe
** E band Channels 4, 7 and 8 have been removed to prevent transmitting outside of
designated Amateur radio frequencies
Band Number
Band Number
Channel Number
Channel Number
Available Frequencies* (mHz)
1 2 3 4 5 6 7 8 A B E F R L26
7
1
2
5 6 4 3
EU Frequency Chart
†
†
Frequency sets have been limited to prevent transmitting outside of designated
CE Frequencies.
SPMVT1000
1. Camera connector
2. Servo connector (Flight Controller)
3. Power LED (White)
4. Power level LEDs (Green)
5. Channel LEDs (Red)
6. Band LEDs (Blue)
7. Antenna connector
See the frequency table below to fi nd the desired video channel and band. The
video transmitter band and power level are changed using the button on the
transmitter or the Spektrum™ VTX control system.
NOTICE: Never power on the video transmitter without the antenna installed.
Powering on without the antenna will damage the video transmitter. This damage is
not covered under warranty.
Channel and Band Selection:
The LEDs illluminate as indicated on the diagram to show Channel and Band.
The buttons will not function when the video transmitter is plugged into
the fl ight controller. Access the frequency and power level options from the
Spektrum transmitter control menu, or from the On Screen Display
Power Level Selection:
All green LEDs off means RF is off, one fl ashing green LED is Pit mode, one
solid green LED is 25mW, two solid green LEDs is 200mW, three solid green
LEDs is 600mW.
IMPORTANT: Do not kink or cut the antenna adaptor or antenna wires. Antenna
wires are coaxial wires, kinks or cuts will degrade performance.
Spektrum VTX Control:
Spektrum control signals include a special command system to manage
frequencies and power output on video transmitters. Compatible video
transmitters can be managed from this menu by connecting a signal wire from
the aircraft receiver to the video transmitter. See the video transmitter manual
for more information.
To apply changes to the video transmitter from the VTX menu of a compatible
Spektrum Transmitter with Spektrum AirWare™ fi rmware:
1. Power on the video transmitter and ensure it is properly connect to the
aircraft receiver.
2. From the Model Adjust menu, select Video Tx.
3. Adjust the Band, Channel frequency, Power level and Mode to the desired
values.Pit mode sets the video transmitter output to very low power for
testing in the pits. Do not attempt to fl y using pit mode. Race mode sets the
video transmitter output to normal power.
4. Select SEND to apply the changes. The video transmitter must be properly
connected and powered on to apply changes.
Specifi cations
MODEL SPMVT1001 SPMVT1001EU
Transmitter
Frequency (MHz) Wideband FM
Modulate
Wideband FM
Modulate
Video Format NTSC NTSC
Output Impedance 50 Ohm 50 Ohm
Output Power
Off, 25mW, 200mW,
600mW selectable
Off, 25mW
Input Voltage DC 5V DC 5V
Camera Output
Voltage
DC 5V DC 5V
Antenna Connector MMCX MMCX
Recommended
Camera
SPMVC602 SPMVC602