E-FLITE Mini Ultra Stick Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 36

background image

Wing Preparation

Required Parts

• Fuselage

• Wing

• Control horn (2)

• 6-channel receiver

• Servo w/hardware (2)

• 6" Y-harness

• Servo extension, 3"

• 4-40 x 3/4" socket head screw (2)

• 3mm washer (2)

• Micro control connector (2)

• 2mm x 4mm screw (2)

• Micro control connector backplate (2)

• 5" pushrod wire (2)

Required Tools and Adhesives

• Thin CA

• Medium CA

• Ruler

• Drill

• Drill bit: 3/32"

• Screwdriver, #0 Phillips

Note

: For the optional Quad Flap modification,

please refer to information on Page 25.



1. Install the aileron servo into the wing. The servo

lead will exit the hole in the bottom center of the
wing. Attach one side of a 6" Y-harness to the
servo lead. We suggest you then hook up the
Y-harness to a 3" servo extension. The 3" servo
extension can remain permanently connected to
your receiver so you do not have to unplug wires
from your receiver each time you disconnect and
remove the wing.

22

«
...
20
21
22
23
24
...
»

Содержание Mini Ultra Stick





































Отзывы:

Нет отзывов

Похожие инструкции для Mini Ultra Stick

Бренд: Dancing Wings Hobby Страницы: 2

Бренд: Jamara Страницы: 12

P-47 Thunderbolt

Бренд: Jamara Страницы: 12

Бренд: Fisher-Price Страницы: 16

IDF Merkava Mk.IV

Бренд: Eduard Страницы: 6

Бренд: Mega Bloks Страницы: 32

Бренд: Ripmax Страницы: 20

Бренд: Radio control model Страницы: 8

Бренд: Badger Basket Страницы: 6

Бренд: marklin Страницы: 32

Бренд: Lionel Страницы: 2

Бренд: Faller Страницы: 16

Lockheed-Martin F-117A Nighthawk

Бренд: REVELL Страницы: 10

Бренд: Faller Страницы: 12

B-17E/F engines

Бренд: Eduard Страницы: 2

0067 85006700200

Бренд: Monogram Страницы: 33

Techno Gears Marble Mania Twister

Бренд: The Learning Journey Страницы: 62

Бренд: marklin Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды