background image

21

E-flite Hurricane 25e PNP/BNF Assembly Manual

EN

Daily Flight Checks

  1. Check the battery voltage of the transmitter 

battery. Do not fly below the manufacturer’s 

recommended voltage. To do so can crash  

your aircraft.

When you check these batteries, ensure you have the 

polarities correct on your expanded scale voltmeter.

  2. Check all hardware (linkages, screws, nuts, and 

bolts) prior to each day’s flight. Be sure that binding 

does not occur and that all parts are properly 

secured.

  3. Ensure all surfaces are moving in the  

proper manner.

  4. Perform a ground range check before each day’s 

flying session.

  5. Prior to starting your aircraft, turn off your 

transmitter, then turn it back on. Do this each time 

you start your aircraft. If any critical switches are on 

without your knowledge, the transmitter alarm will 

sound a warning at this time.

  6. Check that all trim levers are in the  

proper location.

  7. All servo pigtails and switch harness plugs should 

be secured in the receiver. Make sure the switch 

harness moves freely in both directions.

NOTICE

: When finished flying, never keep the 

airplane in the sun. Do not store the aircraft in 

a hot, enclosed area such as a car. Doing so 

can damage the foam.

Limited Warranty

WHAT THIS WARRANTY COVERS

Horizon Hobby, Inc. (“Horizon”) warrants to the 

original purchaser that the product purchased (the 

“Product”) will be free from defects in materials and 

workmanship at the date of purchase. 

WHAT IS NOT COVERED

This warranty is not transferable and does not cover 

(i) cosmetic damage, (ii) damage due to acts of God, 

accident, misuse, abuse, negligence, commercial use, 

or due to improper use, installation, operation or 

maintenance, (iii) modification of or to any part of the 

Product, (iv) attempted service by anyone other than 

a Horizon Hobby authorized service center, or (v) 

Products not purchased from an authorized Horizon 

dealer. 
OTHER THAN THE EXPRESS WARRANTY ABOVE, 

HORIZON MAKES NO OTHER WARRANTY OR 

REPRESENTATION, AND HEREBY DISCLAIMS ANY 

AND ALL IMPLIED WARRANTIES, INCLUDING, 

WITHOUT LIMITATION, THE IMPLIED WARRANTIES 

OF NON-INFRINGEMENT, MERCHANTABILITY 

AND FITNESS FOR A PARTICULAR PURPOSE. 

THE PURCHASER ACKNOWLEDGES THAT THEY 

ALONE HAVE DETERMINED THAT THE PRODUCT 

WILL SUITABLY MEET THE REQUIREMENTS OF THE 

PURCHASER’S INTENDED USE. 

PURCHASER’S REMEDY

Horizon’s sole obligation and purchaser’s sole and 

exclusive remedy shall be that Horizon will, at its 

option, either (i) service, or (ii) replace, any Product 

determined by Horizon to be defective. Horizon 

reserves the right to inspect any and all Product(s) 

involved in a warranty claim. Service or replacement 

decisions are at the sole discretion of Horizon. Proof 

of purchase is required for all warranty claims.  

SERVICE OR REPLACEMENT AS PROVIDED UNDER 

THIS WARRANTY IS THE PURCHASER’S SOLE AND 

EXCLUSIVE REMEDY.

LIMITATION OF LIABILITY

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, 

INDIRECT, INCIDENTAL OR CONSEQUENTIAL 

DAMAGES, LOSS OF PROFITS OR PRODUCTION OR 

COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF 

WHETHER SUCH CLAIM IS BASED IN CONTRACT, 

WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY 

OR ANY OTHER THEORY OF LIABILITY, EVEN IF 

HORIZON HAS BEEN ADVISED OF THE POSSIBILITY 

OF SUCH DAMAGES. Further, in no event shall the 

liability of Horizon exceed the individual price of the 

Product on which liability is asserted. As Horizon 

has no control over use, setup, final assembly, 

modification or misuse, no liability shall be assumed 

nor accepted for any resulting damage or injury. By 

the act of use, setup or assembly, the user accepts all 

resulting liability. If you as the purchaser or user are 

not prepared to accept the liability associated with the 

use of the Product, purchaser is advised to return the 

Product immediately in new and unused condition to 

the place of purchase.

LAW

These terms are governed by Illinois law (without 

regard to conflict of law principals).  This warranty 

gives you specific legal rights, and you may also have 

other rights which vary from state to state.  Horizon 

reserves the right to change or modify this warranty at 

any time without notice.

Warranty Services

QUESTIONS, ASSISTANCE, AND SERVICES

Your local hobby store and/or place of purchase 

cannot provide warranty support or service. Once 

assembly, setup or use of the Product has been started, 

you must contact Horizon directly. This will enable 

Horizon to better answer your questions and service 

you in the event that you may need any assistance. 

For questions or assistance, please direct your 

email to [email protected], or call 

877.504.0233 toll free to speak to a Product Support 

representative. You may also find information on our 

website at www.horizonhobby.com.

Содержание Hurricane 25e TM



























Отзывы: