E+E Elektronik EE772 Скачать руководство пользователя страница 19

Страница: 19 / 32

MAINTENANCE

7.1. Removal of the Sensing Probe of the Gauge Mounting Block

Gauge mounting block without hot tap valve

Make sure that the pipe line is depressurized!

•

Loose the retainer nut and pull the sensor probe from the gauge mounting block.

•

Operation without the flow sensor installed page 10.

7.2. Removal of the Sensing Probe of the Gauge Mounting Block with Hot Tap Valve

The sensor can be removed under pressure without flow interruption.

•

Turn the gauge mounting block with hot tap valve with the hand without tools (anti-clockwise rotation) in

the position SERVICE - CLOSE.

•

Only if the gauge mounting block with hot tap valve is fully in the position SERVICE - CLOSE the sensor

is hermetically sealed against the pressurized line.

•

Loose the retainer nut slowly. Let the air exhaust slowly and make sure that is was only the relief pres-

sure and the gauge mounting block with hot tap valve is hermetically sealed.

•

Loose the retainer nut and pull the sensor probe from the gauge mounting block with hot tap valve.

•

Operation without the flow sensor installed page 10.

The sensor head is sensitive. Use the protection cap for transport and storage!

7.3. Cleaning of the Sensing Element

Do not use an abrasive cleaning agent, an organic solvent containing halogen or acetone.

•

Clean the head of the sensor probe by carefully swirling in warm water of isopropyl alcohol. It is

recommended to use isopropyl alcohol if the pollution is crease or oil.

The sensor should not be touch by fingers or solid objects like screwdrivers or brushes!

•

Leave the sensor to dry in ambient air.

REPLACEMENT PARTS / ACCESSORIES

8.1. Order Code Replacement Sensor

Replacement Sensor

PE772-

Type

Compact ri-le

flow direction right to left

T19

Compact le-ri

flow direction left to right

T20

Remote probe

Measuring range

High - 0...200 m/s

(656.2 ft/s)

HV33

Measurement valve for

pipe diameter

DN40

N40

DN50

N50

DN65

N65

DN80

N80

Mounting

Gauge mounting block

TG2

Gauge mounting block with hot tap valve

TG3

Electrical connection

Cable gland and screw terminals

no code

1 plug for power supply and outputs

Содержание EE772

































Результаты поиска

Содержание EE772

Отзывы:

Похожие инструкции для EE772

Бренды по названию

Популярные бренды

E+E Elektronik EE772, Руководство пользователя

Результаты поиска

Содержание EE772

Отзывы:

Похожие инструкции для EE772

Бренды по названию

Популярные бренды