E+E Elektronik EE772 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 32

background image

8

3.2. Determining Installation Site

•

The installation site should be easy accessible and free of vibrations and shocks.

•

Observe at least 260 mm (10.24 inch) clearance above the housing with the signal conditioning, in

order to be able to remove the sensing probe if necessary.

•

The ambient temperature should not exceed the value as stated in the specifications (see page

20) – consider heating by radiation.

•

Air purity on the installation site according to ISO 8573-1:2010: at least class 3.4.4

•

The fluid should not condense at the installation site. Condensation on the tip of the sensing probe

must be avoided.

•

In compressed air systems, the installation must be downstream of the dryer. If there is no dryer, at

least steam trap and suitable filter must be present.

•

Observe the direction of the flow by the installation (see page 10).

•

Observe the recommended straight pipe lengths up and downstream, in order to warrant the speci-

fied measurement accuracy.

•

The flow sensor should be installed as far as possible from any flow disturbance. Valves or check-

valves should be installed in a respective distance from the flow sensor.

3.3. Installation Position

Make sure that the arrow on the tip of the sensing probe is pointing in the direction of the flow.

++ ... recommended installation position

+ ..... not recommended if there is vibration on the pipeline

- ...... not recommended

Model

Vertical Mounting

Compact

Remote

+

++

Horizontal Mounting, sensor upwards

++

++

Horizontal Mounting, sensor downwards

-

-

Horizontal Mounting, sensor across

+

++

«
...
6
7
8
9
10
...
»

Содержание EE772

































Отзывы:

Нет отзывов

Похожие инструкции для EE772

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 69

Бренд: Keithley Страницы: 32

Бренд: Unico Страницы: 10

Бренд: Omicron Lab Страницы: 33

Бренд: Omicron Lab Страницы: 21

Бренд: Omicron Lab Страницы: 22

Бренд: Vectornav Страницы: 114

Бренд: Vega Страницы: 28

Бренд: Vega Страницы: 20

Бренд: Yamaha Страницы: 31

Бренд: ISKRAEMECO Страницы: 12

RAVTD1760WS Series

Бренд: Ravaglioli Страницы: 24

Бренд: Parkside Страницы: 199

Бренд: Hanna Instruments Страницы: 28

Бренд: Vega Страницы: 20

LaserRange-Master T4 Pro

Бренд: LaserLiner Страницы: 68

Бренд: delta-mobrey Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды