Dynamix RC 903-V35FE1 Скачать руководство пользователя страница 21

Страница: 21 / 26

5. Equipment installation and Preparation

5.1. Installation preparation

Make sure that the E1 line cable matches the equipment model connected to it.

The default effective interface is 75

Ω

BNC. If user wants to use BALANCED

interface, please set the 6

group of dip-switches on the bottom.

Usage of E1 balanced signal line

Definitions of 120

Ω

balanced interface are as follows:

pin 8

Title

TD+

TD-

Not in

use

RD+

RD-

Not in

use

Not in

use

Not in

use

Definition

Output-

Input+

Input-

When 120

Ω

balanced interface connects with other devices, it is required to make sure of

the pin definition of other devices. The pin connection method of twisted-pair on both ends
is shown as follow:

RC series converter BALANCE-RJ45

E1 transmission device balanced

interface

Signal output

Signal input

Attention:

When connecting the twisted-pair, TD

and TD

should be twisted in pairs, and

so do RD

and RD .

5.2. Cautions when the power is on

Hot-swapping V.35 interface is forbidden

It is suggested that the protecting ground (middle of the adapter) be connected first
when using DC –48V device. Note that inverse connection of positive and negative

Содержание RC 903-V35FE1



























Результаты поиска

Содержание RC 903-V35FE1

Отзывы:

Dynamix RC 903-V35FE1, Руководство пользователя, Страница: 21 / 26

Результаты поиска

Содержание RC 903-V35FE1

Отзывы: