Dynamix RC 903-V35FE1 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 26

Dynamix RC 903-V35FE1 Скачать руководство пользователя страница 16

5

th

bit

6

th

bit

7

th

bit

8

th

bit

5

th

bit

6

th

bit

7

th

bit

8

th

bit

ON

ON

ON

ON

OFF

OFF

OFF

OFF

2) There is no PCM equipment occupying Sa bit connecting in series in the E1 link
3) The local and remote equipment should not all be set to the transparent mode.

As shown in the above figure, if the above conditioned is fulfilled, the related clock
mode and bandwidth could be set. If the connection of E1 is correct, the local LOOP
indicator is Flashing, which means that the remote E1 interface loop-back is
successful. When the Router at the local site is checking the interface, the
loop-back status could be shown.

Switch for function selection SW6

:

SW6 switch definition:

1

st

bit

2

nd

bit

3

rd

bit

4

th

bit

5

th

bit

6

th

bit

7

th

bit

8

th

bit

Definition

Fault

pass
through

Reserved

Reserved Reserved

Selection of the type of E1interface

impedance

ON

Enable

OFF

Disable

Normal

Normal

Normal

E1 interface type-user could set

according to practical application. The

default is 75

Ω

BNC.

1. 1

st

bit: Selecting switch for fault pass through (default OFF)

1

st

bit

Fault pass through

ON

Enable

OFF

Disable

When the fault pass through function is enabled, the E1 sending and receiving side alarm
is transmitted to DCD and CTS signal of the V.35 interface. When the fault pass through
function is disabled, the DCD and CTS signal of the V.35 interface is always effective.
If there is local alarm on the Converter, it means that there is fault at the E1 receiving side,
therefore the DCD signal at the V.35 interface will be closed, and there is reflection at the
DTE equipment.
If there is remote alarm on the Converter, it means that there is fault at the E1 sending
side, therefore the CTS signal at the V.35 interface will be closed, and there is reflection at
the DTE equipment.
The DSR signal of this equipment is effective after power on.

2. 2

nd

3

rd

and 4

th

bit: Reserved switch (default OFF)

These converters are reserved configuration switches for test. When the
equipment is working, they should all be in the OFF status.

3. 5

th

6

th

7

th

and 8

th

bit: selecting switch for the type of E1 interface

impedance. (Default ON ON ON OFF)

75

Ω

BNC unbalance interface effective

120

Ω

RJ-45balanced interface

effective

15

«
...
14
15
16
17
18
...
»

Содержание RC 903-V35FE1



























Отзывы:

Нет отзывов