manualshive.com logo in svg

Dynamic Engineering PCIeBiSerialDb37-LM9, Руководство пользователя

Поделиться
Скачать
Dynamic Engineering PCIeBiSerialDb37-LM9 Скачать руководство пользователя страница 37

                          

Embedded Solutions

                          Page  37

Loop-back

The Engineering kit includes reference software, utilizing external loop-back tests.

The test set-up included PcieBiSerialDb37Lm9 and loop-back plug.  The Pin numbers
are for the interconnections on the Loop-back plug.  The IO names can be used to
accommodate a different set-up. The loop-back plug is a DB37 connector with the
interconnections protected with a connector shell.

Signal                        From              To                   Signal

7

13

GPIO_0-

8

14

GPIO_6-

26

32

GPIO_1-

27

33

GPIO_7-

9

15

GPIO_2-

10

16

GPIO_8-

28

34

GPIO_3-

29

35

GPIO_9-

11

17

GPIO_4-

12

18

GPIO_10-

30

36

GPIO_5-

31

37

GPIO_11-

RTS+

1

20

CTS+

RST-

2

21

CTS-

S

3

22

SENDDATA-

4

23

RXDATA-

SEN

5

24

R

SENDTIMING-

6

25

RXTIMING-

Содержание PCIeBiSerialDb37-LM9












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды