Dynacraft 24V TRAIL RACER Скачать руководство пользователя

Страница: 27 / 32

TROUBLE SHOOTING GUIDE

Problem

Possible Cause

Solution

Ride-on toy

does not run

Undercharged

battery

Charge the battery. A new battery should have

been charged for at least 18 hours before using

the ride-on toy for the ﬁrst time. After ﬁrst-time

use, recharge the battery for at least 12 hours after

each use. Never charge the battery longer than 30

hours.
Check all connectors. Make sure the battery

connector is tightly plugged into the wire

connector, and that the charger is plugged into the

wall outlet.
Make sure that there is power ﬂow to the wall

outlet.

Tripped thermal

fuse

The thermal fuse may “trip” and shut down

operation if the ride-on toy is overloaded or the

driving conditions are too severe. Once a fuse has

“tripped”, remove your foot from the pedal and

wait approximately 2 minutes before operating the

ride-on toy again. To avoid repeated automatic

shutdowns, do not overload the ride-on toy by

exceeding the 130 Ib maximum weight capacity or

by towing anything behind the ride-on toy. Do not

drive up hills or run into ﬁxed objects, which can

cause the wheels to stop spinning while power is

still being supplied to the motor.

Electrical switch

damage

The electrical switches can become corroded due to

exposure to water or moisture, or can jam due to loose

dirt, sand or gravel. Please contact our Customer

Service Team. dynacraftwheels.com/contact

Dead battery

Check all wires and connectors. Make sure the

battery connector is tightly plugged into the

wire connector and that there are no loose wires

around the motor.
If your battery is old or if you have not followed

Battery Care instructions, your battery may be

dead. Replace only with an original 24V 7AH

battery. Do not use non-original substitute parts.

Motor damage

Please contact our Customer Service Team.

dynacraftwheels.com/contact

Содержание 24V TRAIL RACER

































Результаты поиска

Содержание 24V TRAIL RACER

Отзывы:

Похожие инструкции для 24V TRAIL RACER

Бренды по названию

Популярные бренды

Dynacraft 24V TRAIL RACER, Руководство пользователя

Результаты поиска

Содержание 24V TRAIL RACER

Отзывы:

Похожие инструкции для 24V TRAIL RACER

Бренды по названию

Популярные бренды