Dynacord DSA 8405, Руководство пользователя

Страница: 20 / 25

DIGITAL SYSTEM AMPLIFIER
Owner‘s Manual / Bedienungsanleitung 35
DSA 8805
Amplifier at rated conditions, all channels driven, rated loads, unless otherwise specified.
1) Output Mode 2
Ω
(500 W at 2
Ω
, 250 W at 4
Ω
, 125 W at 8
Ω
)
2) Output Mode 4
Ω
(500 W at 4
Ω
, 250 W at 8
Ω
)
3) Output Mode 70 V
4) Output Mode 100 V
5) Depending on the ambient temperature, the unit might reduce the output power at 2
Ω
load
6) 50 Hz High Pass is automatically activated in 70 V / 100 V output mode
7) 140 V at 20
Ω
8) 200 V at 40
Ω
9) Due to the mains voltage situation in Japan the values for the maximum output power can be decreased by 15%
10) Depth of the unit without rack ears (detachable): 380 mm
Load Impedance
Low Impedance Mode High Impedance Mode
2
Ω 1
4
Ω 2
8
Ω 2
70 V / 10
Ω 3
100 V / 20
Ω 4
Maximum Midband Output Power
THD = 1%, 1 kHz, 4 channels driven
500 W
5 500 W
250 W
VLD: 500 W
500 W 500 W
Rated Output Power
THD < 0.3%, 20 Hz
6
...20 kHz, 8 ch. driven
450 W 450 W
225 W
VLD: 450 W
450 W 450 W
Maximum Bridged Output Power
THD= 1%, 1 kHz
-
1000 W
1 1000 W
1000 W
7
1000 W
8
Maximum RMS Voltage Swing
THD = 1%, 1 kHz
32 V 45 V
45 V
VLD: 63 V
70 V 100 V
Power Bandwidth
THD = 1%, ref. 1 kHz, half power @ rated load
10 Hz...25 kHz 50 Hz...25 kHz
Voltage Gain , ref. 1 kHz
32 dB 32 dB 32 dB 33 dB 36 dB
Input Sensitivity , rated power, 1 kHz
0.775 V
(+0.0 dBu)
1.1 V
(+3.0 dBu)
1.1 V
(+3.0 dBu)
1.55 V
(+6.0 dBu)
1.55 V
(+6.0 dBu)
THD at rated output power, MBW = 80 kHz, 1 kHz
< 0.05%
IMD-SMPTE , 60 Hz, 7 kHz
< 0.05%
DIM30 , 3.15 kHz, 15 kHz
< 0.02%
Maximum Input Level
+22 dBu (9.76 V
rms
)
Crosstalk , ref. 1 kHz, at rated output power
< -80 dB
Frequency Response , ref. 1 kHz, 8
Ω
load
15 Hz
6
...30 kHz (±1 dB)
Input Impedance , active balanced
20 k
Ω
Damping Factor , 1 kHz, 8
Ω
> 240
Slew Rate
28 V/
μ
s
Signal to Noise Ratio Amplifier , A-weighted
98 dB 100 dB 100 dB 104 dB 106 dB
Output Noise , A-weighted
< -66 dBu < -65 dBu < -65 dBu < -65 dBu < -64 dBu
Output Stage Topology
Class D
Power Requirements (factory configured)
220-240 V, 50-60 Hz or 120 V, 50-60 Hz or 100 V
9
, 50-60 Hz
Power Consumption , 1/8 maximum output power
930 W
Protection
Audio Limiters, High Temperature, DC, HF, Short Circuit, Peak Current Limiters, Inrush
Current Limiters, Turn-on Delay, Mains Circuit Breaker Protection, Mains Over/Under-
voltage Protection
Cooling
Front-to-Rear, temperature controlled fans
Ambient Temperatur Limits
+5 °C...+40 °C (40 °F...105 °F)
Safety Class
I
Dimensions (W x H x D), mm
481 x 88.0 x 421
10
Weight
13.9 kg (28.7 lbs)
Optional:
Rear-rackmount
D113223 (RMK-15)