Dynacord DPC 8000 Скачать руководство пользователя страница 24

Страница: 24 / 38

Operation

Indicators

The meanings of the call station LED indicators are summarized below. Standard configuration
of the call station is assumed.

LED

Status

Description

Zone (green)

Off

Circuit or group not selected

Illuminated green

•

Circuit or group selected

•

Special function activated

•

Direct call activated

Zone (yellow)

Off

Circuit or group not assigned

Flashing yellow

Circuit or group assigned (alarm or
evacuation)

Illuminated yellow

•

Announcement mode: Circuit or group
assigned (everything except alarm,
evacuation, or background music)

•

Program assignment mode: Circuit or
group cannot be assigned with
background music

↑

Off

System is switched off (standby)

Illuminated green

System is switched on and ready for
operation

Flashing green

System has been switched on and is
booting up (activation process)

↓

Off

Pressing the button does not do anything –
the action cannot be stopped

Illuminated green

Pressing the button ends an event that has
already started

DEL

Off

No all-call selected

Illuminated green

All-call pre-selection

↵

Off

The selected circuits are free and a call can
be made

Illuminated green while the
speaker button is pressed

The announcement is being transmitted

Green, flashing slowly

A call station with lower priority is currently
transmitting an announcement in at least
one selected circuit – this announcement
can be interrupted at the cost of the
currently active call station

8.1

en | Operation

DPC 8000

28-Feb-2013 | |

Содержание DPC 8000







































Результаты поиска

Содержание DPC 8000

Отзывы:

Бренды по названию

Популярные бренды

Dynacord DPC 8000, Руководство пользователя

Результаты поиска

Содержание DPC 8000

Отзывы:

Бренды по названию

Популярные бренды