Safety notes
Safety extra low voltage 24 V DC!
Do not connect directly to the mains supply!
- Connection must be carried out by a certified
electrical technician
- Danger of crushing hands and fingers!
- Keep people away from the operating area of the
drive
- Keep children away from the control
- Observe pressure load diagram of the chain
- Use only in dry rooms
- Suitable for indoor mounting only. Use rain
detector in locations if there is a risk of rain
- Use unmodified original D+H parts only
- Observe mounting instructions of bracket set!
Observe enclosed red safety note!
Intended use
- Chain drive for electric opening and closing of
windows and flaps in the facade and roof area
- Operating voltage 24 V DC
- Useable for smoke ventilation as well as daily
natural ventilation
- Suitable for indoor mounting only
CDC-0252-1-TMS+
CDC-0252-1-TMS+
7/20
99.827.61 1.0/01/18
English
Technical Data
* Programmable with software SCS ** + approx. 20 % switch-off reserve (temporary)
C3*
250 N
Opening and Closing Ranges
O1*
C1*
C2*
O2*
O3*
23 mm
150 N
77 mm
150 N
23 mm
250 N
15 mm
250 N
250 N
Type
CDC-0252-0350-1-TMS+ -R
CDC-0252-0600-1-TMS+ -R
CDC-0252-0800-1-TMS+ -R
Power supply
Nominal force
24 V DC / ± 15 %
250 N**
Nominal current
0,6 A
0,8 A
1,0 A
Nominal stroke length*
350 mm ± 2 %
600 mm ± 2 %
800mm ± 2 %
Running speed: ventilation (SHEV high-speed function)*
O1, O2
O3
C3
C2, C1
6,7 mm/s (9,4 mm/s)
6,7 mm/s (6,7 mm/s)
5 mm/s
5 mm/s
6,7 mm/s (13,6 mm/s)
6,7 mm/s (6,7 mm/s)
6,7 mm/s
5 mm/s
6,7 mm/s (15,0 mm/s)
6,7 mm/s (6,7 mm/s)
6,7 mm/s
5 mm/s
Nominal locking force
Service life
Duty cycle
Housing
Ingress protection
Temp. range
Fire stability
Ambient humidity
Emission sound pressure level
Additional functions*
approx. 1500 N
>20.000 double strokes
30% (with cycle time 10 min.)
Aluminium powdercoated (~ RAL 9006)
IP 32
-5 ... +75 °C
30 min / 300 °C
≤ 90 %, not condensing
LpA 35 dB(A)
≤
Closing edge protection = activated (3 repetitions of stroke);
Locking relief = activated (retraction lift max. 0,2 mm)
WARNING
Read all safety warnings, instructions, illustrations
and specifications provided with this product.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
Observe maximum pressure load of the chain!
Maximum pressure load of chain is not automatically
identical with maximum pressure force of the drive!
100
200
300
400
500
600
700
800
250
300
200
150
100
50
0
Pressure load (N)
Stroke (mm)
Pressure load diagram
Main closing edge
Beside closing edge
Beside
closing edge
Closing edge protection
In the "CLOSE" direction the drive has an active
protection for the main closing edge. If there is an
overload in the closing ranges C3 and C2, the drive
runs "OPEN" for 10 seconds, then "CLOSE" again. If
closing is not possible after three attempts, the drive
remains in this position.
In addition, the drive is equipped with passive
protection. The closing speed in closing range C2
and C1 is reduced to 5 mm/s.
Significantly greater forces can be
exerted at the secondary closing
edges. Danger of crushing hands and
fingers!
Scope of supply
Drive unit with 2.5 m silicone cable.
Depending on the type of window, different bracket
sets are available separately.
Performance features
- Micro processor controlled electronics
- Individually programmable via Powerline (PLP1
and SCS)
- Stroke programming with magnets
- Outstanding quiet performance thanks to acoustic
decoupling of the drive components and reduced
speed in ventilation mode
- Connection via plug connector
- Tandem-safety function for operation of two
CDC-0252-1-TMS+ drives on one sash
Up to two CDC-0252-1-TMS+ drives and one locking
drive can be used in tandem. Combined TMS and
BRV signal.
The BRV signal is only output when in the end
position - this prevents locking drives and modules
from malfunctioning.
During the learning phase, the activated stroke is
transferred to the tandem drive via the TMS+
function.
TMS+ / -BRV function
