DX Engineering DXE-AOKC-17M Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 16

DX Engineering DXE-AOKC-17M Скачать руководство пользователя страница 9

- 9 -

7. Attach two element clamps (6) to the lower bracket (4) using an external tooth washer (5), flat

washer (3), split washer (2) and hex nut (1) as shown.

Note:

If you are also installing the

DXE-AOKB-12M

12 Meter Add-on-kit, the lower brackets

will be both mounted to the same studded band clamps. When installing the two lower
brackets

add

an external tooth washer (5) on each studded band clamp

between

the two

mounting brackets to ensure good electrical connection.

8. Assemble the wire insulator (9) using the 1” hex bolt (19). flat washers (3), split washer (2), hex

nut (1), spring (8) and nyloc hex nut (7) as shown below.

Note the side of the insulator that has

the cupped area.

The spacer (10) is inserted in the large hole in the insulator. When attaching the

spring (8) and nyloc hex nut (7), allow a gap to permit the spring to swivel in place.

5. On end of the lower bracket (4) loosely install the 1” hex bolt (19), flat washers (3), split washer

(2) and nylock hex nut (7) as shown..

Note install the nyloc nut (7) just snug at this point.

It

will be tightened when the element wire is installed.

«
...
7
8
9
10
11
...
»

Содержание DXE-AOKC-17M

















Отзывы:

Нет отзывов