manualshive.com logo in svg

DX Engineering DXE-AOKC-17M, Руководство пользователя, Страница: 8 / 16

Поделиться
Скачать
DX Engineering DXE-AOKC-17M Скачать руководство пользователя страница 8

- 8 - 

3.  Install the wing nut (22), split washer (2), large flat washer (21) and carriage bolt (14) to the 

tuning rod bracket (16) as shown. Just snug the hardware in place so it won’t come loose,  

 
 
 
 
 
 
 
 
 
 
 
4.   Check the 17 Meter coil (18) ends to verify they are in line with the coil. If they are slightly 

bent, you can use pliers to gently and carefully bend them into place. The coil is made from 
aluminum so it is easy to bend. 

 
 
 
 
 
 
 
 
5.  Attach the 17 Meter coil (18) to the upper bracket (13) using the coil bracket (17), 1” long 

carriage bolt (15), external tooth washer (5), flat washer (3), split washer (2) and hex nut (1) as 
shown. 

 
 
 
 
 
 
 
 
 
 
 
6.  Carefully and evenly stretch the coil (18) to fit the coil bracket (17). At the bottom of the coil 

bracket (17) attach the bottom of the coil (18) using the 1” long hex bolt (19), flat washer (3), 
external tooth washer (5), flat washer (3), split washer (2) and hex nut (1) as shown. 

 
 
 
 
 
 
 

Содержание DXE-AOKC-17M

















Отзывы:

Нет отзывов