DX Engineering DXE-7580FS-VA-3 страница 36 Скачать руководство пользователя

Страница: 36 / 40

- 35 -

Vertical Elements Assembly

QTY

Description

4.00” OD x 71.75” long, .25” wall, 5 drilled holes

3.50” OD x 71.75” long, .25” wall, 8 drilled holes

3.00” OD x 72” long, .120” wall, 8 drilled holes

2.75” OD x 48” long, .120” wall, 4 drilled holes

2.75” OD x 48” long, .120” wall, 8 drilled holes

2.5” OD x 72” long, .120” wall, 8 drilled holes

2.25” OD x 72” long, .120” wall, 8 drilled holes

2” OD x 72" long, .120” wall, 4 drilled holes one end, slits one end

1.75” OD x 72” long, .120” wall, slits on one end

1.5” OD x 72” long, .120” wall, slits on both ends

1.25” OD x 36” long, .058” wall, slits on one end

1.125” OD x 36” long, .058” wall, slits on one end

1” OD x 36” long, .058” wall, slits on one end

0.875” OD x 36” long, .058” wall, slits on one end

0.75” OD x 36” long, .058” wall, slits on one end

0.625” OD x 36” long, .058” wall, slits on one end

0.50” OD x 36” long, .058” wall, slits on one end

5/16-18 x 5” Stainless Steel Hex Head Cap Screw

5/16-18 x 4-1/4” Stainless Steel Hex Head Cap Screw

5/16” Stainless Steel Flat Washer

5/16-18 Stainless Steel Nyloc Hex Nut

1/4-20 x 3-1/2” Stainless Steel Hex Head Cap Screw

1/4-20 x 3-1/4” Stainless Steel Hex Head Cap Screw

1/4-20 x 3” Stainless Steel Hex Head Cap Screw

1/4-20 x 2-3/4” Stainless Steel Hex Head Cap Screw

1/4” Stainless Steel Flat Washer

1/4-20 Stainless Steel Nyloc Hex Nut

DXE-ECL-2000 Stainless Steel Element Clamp - 2”

DXE-ECL-1750 Stainless Steel Element Clamp - 1-3/4”

DXE-ECL-1500 Stainless Steel Element Clamp - 1-1/2”

DXE-ECL-1250 Stainless Steel Element Clamp - 1-1/8” to 1-1/4”

DXE-ECL-1000 Stainless Steel Element Clamp - 1”

DXE-ECL-0875 Stainless Steel Element Clamp - 3/4” to 7/8”

DXE-ECL-0625 Stainless Steel Element Clamp - 5/8”

Black Vinyl Cap for 1/2" OD Tube

Note:

This antenna system is normally shipped in several boxes. The hardware parts maybe in more
than one box. The part lists listed above are arranged for ease of assembly.

Содержание DXE-7580FS-VA-3









































Результаты поиска

Содержание DXE-7580FS-VA-3

Отзывы:

Похожие инструкции для DXE-7580FS-VA-3

Бренды по названию

Популярные бренды

DX Engineering DXE-7580FS-VA-3, Руководство пользователя

Результаты поиска

Содержание DXE-7580FS-VA-3

Отзывы:

Похожие инструкции для DXE-7580FS-VA-3

Бренды по названию

Популярные бренды