DWT 742654, Оригинальное руководство пользователя

Страница: 15 / 76

15
English
• Start spraying beyond the bounds of the treated
surface.
• Move the spray gun moving your arm as shown in
figure 9.1, and not only the wrist (see fig. 9.2). The
distance between the spray gun and the treated
surface should be constant - this will ensure that the
material is sprayed evenly.
• Smoothly move the spray gun as shown in figure 9.3.
Each successive strip should partially overlap the
preceding one. Do not delay the spray gun in one
spot - this will cause drips.
• Do not interrupt spraying within the treated surface.
• Do not allow reservoir 5 to empty when working.
Tube 18 should be immersed in the liquid at all times,
otherwise the spraying process will be stopped, and
the surface will be treated unevenly.
Power tool maintenance /
preventive measures
Before carrying out any works on the power tool it
must be disconnected from the mains.
Cleaning of the power tool (see fig. 10-14)
The power tool must be cleaned after the
completion of work.
• Press button 4 so that the residues of the sprayed
material drain into reservoir 5 .
• Unscrew reservoir 5 and discharge the sprayed
material residues. Pour an appropriate solvent into
reservoir 5 and connect it to the spray gun. Shake
the spray gun, then switch it on and spray the solvent
into an empty reservoir. Repeat several times until the
spray gun is absolutely clean. If you have been working
using flexible extension hose 17 , then it should be
installed at this step of the cleaning procedure.
• Wipe the power tool case with a cloth moistened
with an appropriate solvent. Prevent the solvent from
getting into the power tool.
• Disassemble the spray gun as shown in figures 10-11
and 13.
• Unscrew reservoir 5 and wipe it with a clean cloth.
• Remove tube 18 and make sure it is clean. Clean it,
if necessary.
• For model ESP01 - 250 , disassembly and clean
filter 24 with the use of a solvent and a soft brush, then
assembly and put filter 24 in place.
• Using rod 13 clean suction hole 25 , drain hole 26
and nozzle 1 (see fig. 12 and 14).
• Using a brush and solvent, clean all removed parts
and mount them back strictly following the installation
sequence. Please note! Using sharp objects for
cleaning spray gun parts (except for the ports
mentioned above) is strictly prohibited.
• To protect internal parts from corrosion, drop a few
droplets of low viscosity oil into suction hole 25 and
drain hole 26 .
• Assembly operations do in reverse sequence.
Air filter replacing (see fig. 15)
[ESP05-200 T]
• Use a screwdriver to remove the cover 8 (see
fig. 15).
• Replace the air filter 27 .
• Install the cover 8 (the clamps of the cover 8 must
click shut).
Cleaning of the power tool
An indispensable condition for a safe long-term
exploitation of the power tool is to keep it clean.
Regularly flush the power tool with compressed air
thought the ventilation slots 8 .
After-sales Service and Application Service
Our after-sales service responds to your questions
concerning maintenance and repair of your product as
well as spare parts. Information about service centers,
parts diagrams and information about spare parts can
also be found under:
www.dwt-pt.com.
•
Transportation
of the power tools
Categorically not to drop any mechanical impact on
the packaging during transport.
• When unloading / loading is not allowed to use
any kind of technology that works on the principle of
clamping packaging.
Environmental
protection
Recycle raw materials instead of
disposing as waste.
Power tool, accessories and packaging should be
sorted for environment-friendly recycling.
The plastic components are labelled for categorized
recycling.
These instructions are printed on recycled paper
manufactured without chlorine.
The manufacturer reserves the possibility to introduce changes.