background image

4-3

Operation

2

1

3

4

I

A

5

4.1.2 Shutting Down the System

There are several possibilities to shut down the Pronto2K/ProntoHD. 
All possibilities depend on whether the operating system is already 
loaded, or not. Please act accordingly:

With the operating system fully loaded

If the operating system is up and running, there are two ways to shut 
down your video system:
1. Turn the system off by shutting down the operating system the 

usual way.

The operating system will then save your personal settings and once 
the program has ended, the system will turn off.
2. Alternatively, you can initiate a fast shut down by pressing the 

main power switch briefly.

Some settings will be saved and afterwards the system turns off.

With the operating system not completely loaded

If the operating system is not completely loaded, perform the follow-
ing:

Pronto2K/ProntoHD delivered with 2 chassis:

To turn off the video system with the Pronto2K/ProntoHD delivered 
with 2 chassis you have to shut down the main system first. After 
that you can turn off the disk array of the Pronto2K/ProntoHD.

You have to turn off the power on both casings.

For this perform the following:

!

Shut down the main system as described in the procedures 
below.

!

Then shut down the disk array by pressing its main power switch 
until the power supply of this casing turns off.

The Pronto2K/ProntoHD delivered with 2 chassis is then shut down 
and turned off.

The fast shut down may not save all your system data 
and personal settings before the system turns off. Oc-
casionally, this may lead to a loss of system data.

After shut-down wait at least ten seconds before starting the 
system again. This time is needed to safely erase all memory 
banks of the system.

Содержание Pronto2K











































































Отзывы: