manualshive.com logo in svg

DV Systems IS13-5530, Безопасность, установка, обслуживание и эксплуатация

Поделиться
Скачать
DV Systems IS13-5530 Скачать руководство пользователя страница 8

SDIG 

Feb ‘15 

 

- 8 -

Lubrication 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Initial Start-up. 

Each Compressor Unit built is extensively tested at the 
factory before shipment. The Unit is shipped with the 
original oil in it as was used for testing purposes. 
 
Check the oil level and for any oil leaks on a daily 
basis. This must be done when the Unit is off. Top up 
the Oil level on a monthly basis. 
 
Use only DV Systems Premium Compressor Oil. Also, 
do not mix the DV Systems oil with any other lubricant. 
 

Oil Changes. 

Drain the existing oil from the Unit. Running the Unit 
prior to draining the oil will ensure that the oil will drain 
relatively quickly. 
 
Fill the Oil Reservoir to the center of the Oil Sight 
Glass. Do not under or overfill. See drawing below. 
 

 

Do not attempt to operate the Unit without 
first checking whether there is oil in the 
Pump Crankcase. Add oil as required. 
Serious damage may result from use, 
however limited, without oil. 

 

 

Use of improper oil may negatively affect 
Compressor performance or shorten Unit life. 
Resulting problems are not covered by the 
DV Systems Warranty. 

 

 

With limited Compressor use or installing in a 
very humid environment, condensation 
(water) may form in the Crankcase with the 
oil. If this occurs, change the oil more often 
than indicated on the Maintenance Schedule. 

The following oils are available from your DV 
Systems Distributor. 

 

DV Systems Premium 

Mineral

 Oil 

is 

shipped in the Pump. 

30 Weight:  ‘PR-31-4’ 

 

DV Systems Premium 

Synthetic

 Oil 

is 

used in high heat or high duty applications. 

20 Weight:  ‘OJ-2000’ 

 

The following Maintenance Kit is available from your 
DV Systems Distributor. The Kit includes both the Oil 
and Filter. 

 

Kit c/w 20 Weight 

Mineral

 Oil 

DV Systems Pump 

Kit Part Number 

DEV-55 

MK-55 

 
Note:

  Though the Synthetic Oil is available, 

it must be purchased separately as it 
is not included in a Kit. 

Proper Oil 

Level 

Oil Drain 

Содержание IS13-5530
















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды