Dux 135DC5N Скачать руководство пользователя страница 12

Owner’s Manual – Prodigy 4 & 5

10

H3109    3109    Rev. L

The operation of the water heater must be 
tested by the installer. This work must only 
be done by a licensed tradesperson.

Test for Leaks:

Check the water inlet, water outlet and gas 
inlet pipe work and connections for leaks.

Test the Gas Inlet Pressure:

For correct operation of the water heater, 
the gas inlet pressure must be at least:
  

Natural Gas 

1.13 kPa 

 

Propane  

2.75 kPa

To test the gas inlet pressure, follow the 
procedure below. If the pressure is less 
than the above value, there could be a 
problem with the gas meter or supply 
pipe size. 
1.  Ensure the water heater has been 

filled with water and the gas isolation 
valve is turned off.

2.  Remove the lower of the two hex 

head screws on the right hand side 
of the gas control valve and fit a 
manometer to the spigot.

3.  Turn on the gas isolation valve and 

light the water heater. See Lighting 
the Water Heater on page 8.

4.  If necessary, adjust the control knob 

until the main burner lights.

5.  With the main burner alight, measure 

the pressure.

6.  Turn the thermostat knob to the “•” 

(off) position and turn off the gas 
isolation valve.

7.  Disconnect the manometer and 

replace the screw removed at  
step 2.

Test the Gas Test Point Pressure:

For correct operation of the water heater, 
the gas test point pressure must be 
within 5% of the value marked on the 
compliance plate.

4 Star:  

To test the gas test point 
pressure, follow the same 
procedure used for the gas inlet 
pressure except that the upper of 
the two hex head screws is to be 
removed at step 2. 

5 Star:  

To test the gas test point 
pressure, follow the same 
procedure used for the gas inlet 
pressure except that the M4 
button head screw on the right 
hand side of the relay valve is to 
be removed at step 2. A 2.5mm 
allen key is supplied with the 
water heater for this purpose.

If the pressure is not within 5% of the 
marked value, contact Dux After Sales 
and Service for advice.

Final Checks:

•  Turn on the gas isolation valve and 

light the water heater.

•  Make sure there are no gas leaks 

from either of the two screws 
removed during gas pressure testing.

•  Set the gas control knob to position 

“6” unless hot water is not required.

•  Replace the access cover.
•  Hand this manual to the occupier of 

the premises and explain the lighting 
procedure if required.

Testing

Содержание 135DC5N





















Отзывы: