DUROMAX DuroStar DS13000DX Скачать руководство пользователя страница 39

Страница: 39 / 84

Pull the recoil start

Open choke

After the engine has started, push the choke left to the OPEN
position as the engine warms up.

Turn breaker ON/ Connect

The breaker is located on the right side of the front power

panel. Flip the breaker up to allow the power to flow to the

receptacles. Connect your devices to the receptacles on the

front panel. Start with the largest loads first.

Close choke

The choke lever is located above the air filter to the left

of the recoil start. Slide the lever to the right to cut the air
supply and allow more gas into the engine to start.

The recoil start is located on the left side panel next to the air

filter. Pull the recoil handle slowly until resistance is felt, then

quickly pull the recoil handle until fully extended.

CAUTION

: Release the recoil handle only after

the cord has retracted. Releasing the recoil

handle while extended may cause harm to

yourself or your

equipment.

Содержание DuroStar DS13000DX





















































































Результаты поиска

Содержание DuroStar DS13000DX

Отзывы:

DUROMAX DuroStar DS13000DX, Руководство пользователя, Страница: 39 / 84

Результаты поиска

Содержание DuroStar DS13000DX

Отзывы: