background image

4.12  Checking the Input Elements

Program 62 checks the input elements.

Set the "Program" switch to "62".

Press the "STOP" key. The program is activated.

Press the input element.
The wiring diagram designation and the switching status of the
input element appear in the display (e.g. "+B25").
The display changes when the switching status of any other input
element is changed.

The switching status "+" means:

By contact switch

=  Open contact

By proximity switch

=  Metal in front of the switch

By reflecting light barrier

=  No reflection

Transmitted light barrier

=  Light beam not interrupted

4.13  Selecting Input Elements

ATTENTION !

All input elements were carefully set at the factory.
The resetting and correction may only be conducted by trained service
personnel.

Program 63 is used for setting the input elements.

Set the " Program " switch to " 63 ".

Press the " STOP " key.
The program is activated.

Set the " Program " switch to the selected input element (see
Table).

Adjust the input element (switching flag, switching cam, etc.) until
the desired switching status appear.

Input

Function

Element

b03

Table forward

b04

Sewing enabled

b05

Transport carriage left

b07

Transport carriage right

b14

Needle thread monitor

b15

Form set slewing

b16

Form set control

b45

Light barrier seam end

b46

Remaining thread monitor

18

Содержание class 743-221






















Отзывы: