DURKOPP ADLER 911-210-3020-10 Скачать руководство пользователя страница 113

Страница: 113 / 128

Decommissioning

Operating Instructions 911-210-10 - 00.0 - 06/2020

111

Decommissioning

To decommission the machine:

Switch off the machine.

Unplug the power plug.

If applicable, disconnect the machine from the compressed air supply.

Remove residual oil from the oil pan using a cloth.

Cover the control panel to protect it from soiling.

Cover the control to protect it from soiling.

Cover the entire machine if possible to protect it from contamination
and damage.

WARNING

Risk of injury from a lack of care!

Serious injuries may occur.

ONLY clean the machine when it is switched off.
Allow ONLY trained personnel to disconnect the
machine.

CAUTION

Risk of injury from contact with oil!

Oil can cause a rash if it comes into contact with
skin.

Avoid skin contact with oil.
If oil has come into contact with your skin, wash the
affected areas thoroughly.

Содержание 911-210-3020-10

































































































































Результаты поиска

Содержание 911-210-3020-10

Отзывы:

Похожие инструкции для 911-210-3020-10

Бренды по названию

Популярные бренды

DURKOPP ADLER 911-210-3020-10, Руководство по эксплуатации

Результаты поиска

Содержание 911-210-3020-10

Отзывы:

Похожие инструкции для 911-210-3020-10

Бренды по названию

Популярные бренды