DURKOPP ADLER 540 - 100 Скачать руководство пользователя

Страница: 7 / 49

Elements of the control panel

Key

Function

If no text field is activated:

–

Change to the parent menu.

If a text field is activated:

–

Change between the figures tenth, unit, ten etc.

–

Change between the lines in the menus. The selected line is
always dark-shadowed.

If a text field is activated:

–

Increase or reduce the value of the respective figure by one or
change between the parameters in case of functions with several
choices, e.g. between “Push button on“ and “Push button off“.

–

Activate the text field. The value can be altered with the keys “

“

and “

“.

If a text field is activated:

–

The set value is taken over.

–

You get back to the main menu from a submenu.

If a text field is activated:

–

An input is aborted. The previous value remains unchanged.

–

The control changes from the sewing mode to the programming
mode. The buttonhole parameters can be altered in this mode.

–

The control changes from the sewing mode or programming mode
to the sequence programming mode.

–

The control changes from the sewing mode to the technician mode.
This mode can only be activated by entering a code

25483

. In this

operating state it is possible to set basic machine parameters and
to call up diagnosis and adjusting programs.

Содержание 540 - 100


















































Результаты поиска

Содержание 540 - 100

Отзывы:

Похожие инструкции для 540 - 100

Бренды по названию

Популярные бренды

DURKOPP ADLER 540 - 100, Руководство по эксплуатации

Результаты поиска

Содержание 540 - 100

Отзывы:

Похожие инструкции для 540 - 100

Бренды по названию

Популярные бренды