DURKOPP ADLER 540 - 100 Скачать руководство пользователя | Manualshive

Страница: 26 / 49

background image

Standard reference position of the needle bar:

–

Switch the machine on and let it move to the initial position.

–

Switch the machine off again.

Correction:

–

Loosen the screws 8 and shift the proximity switch 6 according to
the instructions.

–

Tighten the screws again.

–

Readjust the adjusting sheet, if required.

Chapter 6.3 Setting the

adjusting sheet

.

6.3

Setting the adjusting sheet

The adjusting sheet is used for the quick positioning of the needle bar
in the adjustment positions when the machine is switched off.
–

Needle bar in the centre of the needle hole (reference position)
Bolt 10 abuts on the right flank of the slotted hole.

–

Needle bar in the furthest right entry point with a throw width of 6 mm.
Bolt 10 abuts on the left flank of the slotted hole.

–

Let the machine move to the initial position (e.g. immediately after
switching on).

–

Loosen the screws 11.

–

Shift the sheet in such a way that the right flank of the slotted hole
of the sheet abuts on bolt 10 of the needle bar linkage.

–

Tighten the screws 11 again.

Note

Before adjusting the sheet the settings described in chapter 6.2 must
have been made correctly.

22

11

6
9

10

8

«
...
24
25
26
27
28
...
»

Содержание 540 - 100


















































Отзывы:

Нет отзывов

Похожие инструкции для 540 - 100

Бренд: Singer Страницы: 29

Memory Craft 6300P

Бренд: Janome Страницы: 69

Бренд: Singer Страницы: 99

Бренд: Dixie Narco Страницы: 14

ReadySpace 1610

Бренд: Tennant Страницы: 2

Бренд: Jack Страницы: 23

Бренд: Singer Страницы: 15

Бренд: PowerBoss Страницы: 52

Бренд: Horizon Fitness Страницы: 45

Neofold HS 1250

Бренд: Neolt Страницы: 114

Бренд: Mercury Страницы: 6

Dreamstitcher Portabl 787

Бренд: Reliable Страницы: 1

Бренд: JUKI Страницы: 2

Бренд: JUKI Страницы: 8

Бренд: JUKI Страницы: 10

Бренд: JUKI Страницы: 76

Бренд: Brother Страницы: 12

Бренд: Brother Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды