DURAVIT Pool Скачать руководство пользователя страница 47

Страница: 47 / 52

Problem

Potential cause

Solution

See
page

“Check heater”

•

Fresh water was added

manually

•

The time was changed

•

Malfunction or heating

defect.

Disconnect the pool from

the mains for 3 minutes.

If the error message

appears again within

2 hours, call Customer

Service.

“Connection

defective”

Please call Customer Ser-

vice.

“Water temperature

too high”

CAUTION

Under no

circumstances should you

bathe until the water tem-

perature has fallen again!

Refill with some cold water.

Wait until the system has

cooled down. Temperature

must be reduced below

42 °C/108 °F.

“Water level too low”

Not enough water in the

bath.

Refill the water until the

water level is about 50

mm above the uppermost

jet.

Otherwise:

Please call Customer Ser-

vice.

“Difference

water sensors”

Please call Customer Ser-

vice.

“Wrong PIN”

You have entered the

wrong PIN.

Enter the correct PIN

Forgot PIN?

Enter PIN 2412.

“Timeout when filling”

Pool has not reached

maximum fill level. Pipe

pressure too low, pipe not

supplying enough water.

Check water connection.

Otherwise:

Please call Customer Ser-

vice.

Содержание Pool





















































Результаты поиска

Содержание Pool

Отзывы:

Похожие инструкции для Pool

Бренды по названию

Популярные бренды

DURAVIT Pool, Руководство по эксплуатации

Результаты поиска

Содержание Pool

Отзывы:

Похожие инструкции для Pool

Бренды по названию

Популярные бренды