Duratuf KIWI SHEDS MK3 Скачать руководство пользователя | Manualshive

Страница: 12 / 16

background image

MK3 CLEAR ROOF PANEL (Optional)

12

Step 2:

Position clear roof and flat roof sheet (or second clear panel). The flat roof sheet underlaps one sheet and overlaps the other.
The clear roof panel

overlaps

both roof sheets. Ensure sheet joins are flush at the outside edge then rivet flat sheets to pressed

sheets. Two rivets per join. Centralise roof at the other end and screw in place.

Step 3:

Ensure ridge beam is straight, then nail the clear panel and flat roof sheet (or second clear panel) to ridge beam using one
30mm clout per pan. Position on ridge beam and screw in place using six 50mm roofing screws. Screw one 50mm roofing
screw into ridge beam through each rib on overlap, (one screw per sheet). Mould the soft edge on the flashing down into the
pans of the roof sheet to prevent roof leaks.

Step 4:

Continue to fasten roof sheets as per step 4 on previous page (pg10)

Note:

When screwing through the clear panel, pre

-

drill a 6mm hole.

TOP PLATE

JACK STUD

RIDGE BEAM

30mm CLOUT

RIDGE FLASHING

ROOFING SCREWS

PRESSED ROOF SHEET

CLEAR ROOF

FLAT ROOF

Step 1:

Leave a gap where the Clear Panel is to be fitted. Position the next Roof Sheet. Ensure it overlaps correctly, then rivet togeth-
er, one rivet in the centre and one approximately 600 mm down from the centre on both sides. Fit remaining Roof Sheets,
overlapping and riveting as you go. Nail on first Roof Sheet (refer step 3 on page 10).

Note:

MK2 shown

«
...
10
11
12
13
14
...
»

Содержание SHEDS MK3

















Отзывы:

Нет отзывов

Похожие инструкции для SHEDS MK3

Бренд: Harnois Страницы: 4

Бренд: Sequoia Страницы: 11

Бренд: Shelters4Less Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды