Duratrax Vendetta SC Скачать руководство пользователя страница 3

3

THINGS TO

KNOW

SAFETY PRECAUTIONS

When these safety precautions are 
followed, the Vendetta SC will provide 
years of enjoyment. Use care and good 
sense at all times when operating this radio 
controlled truck. Failure to use this vehicle 
in a safe, sensible manner can result in 
injury or damage to property. You and you 
alone must ensure that the instructions are 
carefully followed and all safety precautions 
are obeyed.

•  Do not operate the Vendetta SC near 

people. Spectators should be behind the 
driver or at a safe distance away from 
the vehicle.

•  Make sure to read the instructions included 

with the battery and charger before 
charging the battery.

•  Do not leave any charger unattended during 

charging. If the battery or charger become 
hot at any time, disconnect the battery 
from the charger immediately! Failure to 
do so may cause permanent damage to 
the charger and battery and may cause 
bodily harm or property damage.

•  Do not cover the air intake holes on the 

charger during charging. This may cause 
the charger to overheat.

•  Do not allow the electronic speed control 

(ESC) or other radio equipment to come 
into contact with moisture. Water can 
cause electronics to short out and can 
cause permanent damage.

•  Always turn on the transmitter before 

turning on the electronic speed control.

•  Always turn off the ESC 

before

 turning off 

the transmitter.

•  Allow the motor and ESC to cool before 

each run.

HELPFUL HINTS

•  Avoid working over a deep pile carpet. If 

you drop a small part or screw, it may be 
diffi cult to fi nd.

•  Place a mat or towel over your work area. 

This will prevent parts from rolling off and 
protect the work surface.

•  Avoid running the truck in cold weather. The 

plastic and metal parts can become brittle 
at low temperatures. In addition, grease 
and oil become thick, causing premature 
wear and poor performance.

•  Test fi t all parts before attaching

them permanently.

SPECIFICATION AND

DESCRIPTION CHANGES

All pictures, descriptions and specifi cations 
found in this instruction manual are subject 
to change without notice. DuraTrax maintains 
no responsibility for inadvertent errors in this 
manual. Visit 

duratrax.com

 for the latest 

updates and information for your model.

WARRANTY

•  DuraTrax

®

 guarantees this kit to be free from 

defects in both material and workmanship at 
the date of purchase. DuraTrax will warranty 
this kit for 90 days after the purchase 
date. DuraTrax will repair or replace, at no 
charge, the incorrectly made part.

•  Make sure you save the receipt or invoice 

you were given when you bought your 
model! It is your proof of purchase and 
we must see it before we can honor the 
warranty. Further, DuraTrax reserves the 
right to change or modify this warranty 
without notice.

•  In that DuraTrax has no control over the 

fi nal user assembly or material used for 
fi nal user assembly, no liability shall be 
assumed nor accepted for any damage 
resulting from the use by the user of the 
fi nal user-assembled product. By the act 
of using the user-assembled product, the 
user accepts all resulting liability.

To return your Vendetta SC for repairs 
covered under warranty, you should send 
your truck to:

Hobby Services

3002 N. Apollo Drive Suite 1

Champaign, Illinois 61822

Attn: Service Department

Phone: (217) 398-0007

9:00 am–5:00 pm Central Time M-F

E-mail: [email protected]

hobbyservices.com

If you are not prepared to accept the 
liability associated with the use of this 
product, you are advised to return this 
kit immediately in new and unused 
condition to the place of purchase.

STRESS-TECH

 PARTS

GUARANTEE

We have engineered the Vendetta SC to 
take the rough and tumble abuse that makes 
R/C fun. We are so confi dent of the quality 
and durability of the Stress-Tech plastic 
parts that we will replace any Stress-Tech 
plastic part you break during the fi rst 12 
months you own the truck. Just send in the 
part to us and we will send you a FREE 
replacement. Please see the parts list for 
the items covered under the Stress-Tech 
guarantee.

To receive your free replacement part 
please send the following to the Hobby 
Services address listed under the warranty 
on the left.

 1. The broken part must be included.

 2.  The part number and description of the 

broken part.

 3.  Copy of the dated invoice or 

purchase receipt.

 4.  Your name, phone number and 

shipping address.

REPAIR SERVICE

Repair service is available anytime.

•  After the 90 day warranty, you can still 

have your Vendetta SC repaired for a 
small charge by the experts at DuraTrax’s 
authorized repair facility, Hobby Services.

•  To speed up the repair process, please 

follow the instructions listed below.

 

1. Under most circumstances return 

the ENTIRE vehicle. The exception would 
be sending in a Stress-Tech part. See the 
instruction under the Stress-Tech Guarantee.

 2. Make sure the transmitter is turned off, 

and all of the batteries are removed.

 3. Send written instructions which include: 

a list of all items returned, a THOROUGH 
explanation of the problem, the service 
needed and your phone number during the 
day. If you expect the repair to be covered 
under warranty, be sure to include a proof 
of date of purchase (your store receipt or 
purchase invoice).

Содержание Vendetta SC

























Отзывы: