manualshive.com logo in svg

Duratech 4426, Инструкция по эксплуатации и справочник по запасным частям

Поделиться
Скачать
Duratech 4426 Скачать руководство пользователя страница 22

14

1 0 7   D R I L L

O P E R A T I N G   I N S T R U C T I O N S

2.2  False Bottom Attachment

The false bottom attachment allows the use of both tanks, front and back, to be used in combination for seed. This will
enable the seed tanks to last longer before refilling during seeding operation.

INSTALLATION

Step 1:

Remove the divider cover (Item #2) from the grain tank by unbolting and setting the cover aside.

Step 2:

Insert the false bottoms right hand (RH) sheet (Item #3) by holding its handles and pushing the
studs into the existing slots found just below the 6” x 24” openings in the center divider as shown in
the accompanying illustration.

Step 3:

Insert the false bottom LH sheet (Item #4) in the same manner as described in Step 2.

Step 4:

Place the side seal retainer RH (Item #5) on the false bottom RH with the rubber seal (Item #9)
fitting in the crimp space provided between the two parts (See Detail A).

Step 5:

Place the side seal retainer LH (Item #6) on the false bottom LH with the rubber seal (Item #9) as in
Step 4.

Step 6:

Place the upper seals (Items #7 and #8) on their respective false bottoms as shown in the
accompanying illustration.

Step 7:

Position the false bottoms by moving them to the left or right so that l/2” exists between the false
bottoms and the seed tank wall (See Detail A).

Step 8:

Place all flat washer, lock washers and nuts (Items #11, #12 and #13) in their respective locations as
shown in the accompanying illustration.

Step 9:

Tighten only the false bottom nuts to secure the false bottoms to the center divider.

Step 10:

Slide the upper seals and the side seal retainers firmly against their respective walls and tighten all
the nuts.

The preceding steps are to be followed in the opposite fashion starting with the last step and proceeding to Step 1 to
bring the drill to its original manner.

Содержание 4426

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды