background image

DURA-BILT PRODUCTS, INC.

Five Year Limited Warranty

 

Dura-Bilt Products, Inc. warrants its manufactured products to the original 

purchaser to be free from defects in materials or workmanship under the terms and 
conditions set forth herein.  All other components and parts carry their own
manufacturers warranties.

 

Within the warranty period, to be confi rmed with copy dated bill of sale, 

Dura-Bilt Products, Inc. will, at its sole option, repair or replace any components 
which the owner has proven to have failed in normal use.  Such repairs or
replacement will be made, at no charge for parts, to the original purchaser.
Provided, however, that the original purchaser shall be responsible
for any transportation or freight costs.  Replacement of materials does not extend 
original warranty period.  This warranty does not include the cost of labor for 
installation of parts.

 

Continuing product developments require that Dura-Bilt Products, Inc. 

retain the right to substitute replacement parts or components of equal quality, if 
necessary.  Normal aging and weathering of materials may result in not being able 
to perfectly match the original colors.

 

This limited warranty does not cover failures due to weather, acts of God, 

abuse, misuse, improper installation, accident, alteration or repair.  Dura-Bilt
Products, Inc.  assumes no responsibility for special, incidental, punitive or
consequential damages or loss of use.

 

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF 

ALL OTHER WARRANTIES AND REMEDIES EXPRESS OR IMPLIED, 
INCLUDING ANY LIABILITY ARISING UNDER THE WARRANTY OF 
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, 
STATUTORY OR OTHERWISE.  THIS WARRANTY GIVES YOU
SPECIFICALLY THESE RIGHTS WHICH MAY VARY BY STATE.

 

This warranty covers products manufactured by Dura-Bilt after 9/1/95.

 

To obtain warranty service, call the Dura-Bilt Products Customer Service Department at 

1-570-596-2000 or write to P.O. Box 188, Wellsburg, NY 14894-0188.  Retain this Warranty for 
your records.

Page 15

Содержание DFSOC-10

















Отзывы: