Duplo DC-616, Руководство по обслуживанию

Страница: 51 / 210

3
Chapter 3
Mechanism
•In principle, do not operate this machine with parts removed.
•When assembling:
•Unless speci
fi ed otherwise, perform the disassembly procedure in reverse.
•Make sure that screw types (radius, length) and locations are correct.
•Be sure to use rosette washers when they are speci
fi ed.
(Rosette washers are used with installation screws to prevent static electricity.)
•To ensure electrical current, a rosette washer is used with the installation screw on
the ground wire. Be sure to use the rosette washer during assembly.
•Always remove the power cord plug from the outlet before starting work.
CAUTION
•Cautions Regarding Disassembly and Assembly
1 Exterior of the Machine
.......................
51
(1) Removing the Cover F (on control panel side)
..
52
(2) Removing the Cover F2 Unit (on control panel side)
.
52
(3) Removing the Cover R2
.................
52
(4) Removing the Cover
.....................
53
(5) Removing the Cover R
..................
53
(6) Removing the Plate
......................
53
(7) Removing the Top Cover
................
53
(8) Removing the Cover (Power supply)
.
54
(9) Removing the Top Cover Interlock Switch
..
54
(10) Removing the Front Cover Interlock Switch
.
55
(11) Removing the Exit Interlock Switch
..
55
2 Paper Feed Section
...........................
56
(1) Removing the Paper Separation Plate 56
(2) Removing the Belt Suction Unit
........
56
(3) Removing the Feed Motor
..............
58
(4) Removing the Suction Fan
..............
58
(5) Removing the Compressor
.............
59
(6) Removing the Compressor Fuse
......
60
(7) Removing the Paper Level Sensor
....
61
(8) Removing the Elevator Upper Limit Switch
..
62
(9) Removing the Elevator Lower Limit Switch
..
62
(10) Removing the Elevator Motor
.........
63
(11) Removing the PPS1
....................
64
(12) Removing the Elevator Down Switch
.
65
(13) Removing the Paper Feed Unit
.......
65
(14) Removing the Blow Fan
...............
66
3 Double Feed Detection Section (Option)
..
67
(1) Removing the Ultrasonic Sensor Unit
.
67
4 CCD Section (Option)
........................
68
(1) Removing the CCD
.......................
68
(2) Removing the PPS2
.....................
69
5 Margin Slitter Section
.........................
70
(1) Removing the Margin Slitter Module
..
70
(2) Removing the Margin Slitter Position Motor/Belt
.
73
(3) Removing the Margin Slitter Home Position Sensor
.
74
(4) Removing the Margin Jam Sensor
....
75
6 Center Slitter Section
.........................
76
(1) Removing the Center Slitter Module
..
76
(2) Removing the Center Slitter Position Motor
.
79
(3) Removing the Center Slitter Home Position Sensor
.
80
(4) Removing the PPS3
.....................
81
(5) Removing the Gutter ON/OFF Sensor
82
7 Cutter Section
..................................
83
(1) Removing the Cutter Module
...........
83
(2) Removing the Cutter Home Position Sensor
..
84
8 Creaser Section
...............................
85
(1) Removing the Creaser Motor and the Belt
..
85
(2) Removing the Creaser Home Position Sensor
.
85
(3) Removing the Crease Blade
............
86
(4) Removing the Crease Lower Blade Home Position Sensor
.
87
(5) Removing the Crease Lower Blade Motor
.
87
(6) Removing the Creaser Lower Blade Encoder Sensor
.
88
(7) Removing the PPS4
.....................
89