Dunlop L.AMA.10.C.L Скачать руководство пользователя страница 3

Страница: 3 / 20

L.AMA.10.C.L

Volkswagen AMAROK

DUNLOP and the Flying D Device are trademarks of Dunlop International Group and are used under license by DSC Nederland B.V.

www.dunlopsystems.nl

1. FOREWORD

This manual provides instructions for the installation of an auxiliary air

suspension kit, developed specifically for the Volkswagen Amarok

(2010—onwards). To ensure correct installation of the kit, it is strongly

recommend that these instructions are read thoroughly before

commencing any installation work. Installation should only be carried out

by a suitably qualified mechanic or specialist installation facility. DSC

Nederland will not accept any responsibility for faults or defects arising

from incorrect installation, which automatically renders the guarantee

invalid.

IMPORTANT : Manufacturer’s Declaration Form

A manufacturer’s declaration form is provided with your kit.

Following installation of the kit please ensure that this form is

completed, signed by a qualified fitter and a copy is returned to

DSC Nederland by post, fax or e-mail. Our e-mail address is:

[email protected]

Содержание L.AMA.10.C.L





















Результаты поиска

Содержание L.AMA.10.C.L

Отзывы:

Похожие инструкции для L.AMA.10.C.L

Бренды по названию

Популярные бренды

Dunlop L.AMA.10.C.L, Руководство по установке

Результаты поиска

Содержание L.AMA.10.C.L

Отзывы:

Похожие инструкции для L.AMA.10.C.L

Бренды по названию

Популярные бренды