Dunlop L.AMA.10.C.L Скачать руководство пользователя

Страница: 19 / 20

L.AMA.10.C.L

Volkswagen AMAROK

DUNLOP and the Flying D Device are trademarks of Dunlop International Group and are used under license by DSC Nederland B.V.

www.dunlopsystems.nl

6. EPILOGUE

DSC Nederland hopes that you enjoy the benefits that your DUNLOP air

suspension system will provide for you. To ensure optimal performance,

we advise that you have your system checked frequently by qualified

personnel. As recommended in the fitting instructions, it is important to

coat all the steel parts with a protective substance such as body wax.

IMPORTANT : Manufacturer’s Declaration Form

A manufacturer’s declaration form is provided with your kit.

Following installation of the kit please ensure that this form is

completed, signed by a qualified fitter and a copy is returned to

DSC Nederland by post, fax or e-mail. Our e-mail address is:

[email protected]

As a condition of your warranty, modifications to the system may only be

carried out by personnel of DSC Nederland.
Enquiries
For general enquiries please contact one of our dealers. You can find

them on our website.

www.dunlopsystems.nl

Содержание L.AMA.10.C.L





















Результаты поиска

Содержание L.AMA.10.C.L

Отзывы:

Похожие инструкции для L.AMA.10.C.L

Бренды по названию

Популярные бренды

Dunlop L.AMA.10.C.L, Руководство по установке

Результаты поиска

Содержание L.AMA.10.C.L

Отзывы:

Похожие инструкции для L.AMA.10.C.L

Бренды по названию

Популярные бренды