Dunkirk DXL-125 Скачать руководство пользователя страница 29

Страница: 29 / 32

APPENDIX A-2 - VENT DAMPER TROUBLESHOOTING

Problem

Possible Cause

Recommended Solution

NO POWER

Between 4 & 1
Between 4 & 2
Between 4 & 3
Damper OPEN
NO COMBUSTION

1. Is gas turned on
2. Operating limit, pressure control, low water cut off not on.

3. Blocked vent switch or flame roll out switch tripped

4. Loose or broken connection
5. Defective component in appliance after vent damper

1. Verify gas is on
2. Verify operating limit, pressure control or low water cut off is

3. Reset or replace blocked vent switch or flame roll out switch

4. Tighten, repair, or replace connection
5. Replace defective component in appliance

Damper Sticks

1. Damper blade obstruction
2. Damper pipe egg shaped, out of round/binding.
3. Crimped end of vent piece inserted in too far

1. Clear the obstruction
2. Restore to damper pipe to round, verify not binding.
3. Correct the condition

Damper Rotates

Continuously

1. Defective damper motor assembly

1. Replace damper motor assembly

Note

For troubleshooting only. Verify damper is in

open position. Use service switch to keep

damper in open position. Place jumper between

2 & 3. If appliance fires, remove jumper and

plug receptacle back into damper controller

plug. If appliance does not fire, replace damper

motor assembly. Do not replace pipe assembly.

If damper motor assembly is not available,

place service switch in hold open position. This

should keep damper in open position and allow

customer to have automatic heat. Return or

replace the motor assembly at your convenience.

Motor assembly carries 18 month limited

commercial warranty from the original date of

purchase. (Refer to form #4294 on vent damper

manufacturers website). Pipe assembly is not

warranted.

Trouble Shooting with Jumper Wire In Place

P/N

240009041

, Rev. C [04/30/2017]

Содержание DXL-125

































Результаты поиска

Содержание DXL-125

Отзывы:

Похожие инструкции для DXL-125

Бренды по названию

Популярные бренды

Dunkirk DXL-125, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание DXL-125

Отзывы:

Похожие инструкции для DXL-125

Бренды по названию

Популярные бренды