DUNIWAY Stockroom Terranova 908A Скачать руководство пользователя

Страница: 26 / 29

D U N I W A Y S T O C K R O O M C O R P .

26 of 29

Trouble Shooting

Error Codes:

Under the staed conditions, Error Codes are shown on the display:

01 = Action Not Allowed at This Time

02 = Parameter Exceeds Limit of Adjustment

03 = A Timeout Occured during Adjustment

05 = Attempt To Change Units While Pascal Lock Engaged

21 = CDG Zero Adjustment Not Allowed at This Pressure

22 = CDG Atmosphere Adjust Not Allowed at This Pressure

Figure 18: Error Codes

Self Test:

If the self-test fails, run the self-test again by turning the power off and then on again.

The folowing sequnce should be executed:

• “beeper”

• indicators for

TORR

MTORR

MBAR

BAR

PASCAL

KPASCAL

GAGE

• 10 LED indicators for set points and other functions

• all four digits will light, including decimal points

• display shows the model number of the instrument,

908A

• display shows software version, e.g.

1.10

If it fails again, call Duniway Stockroom.

Fuses:

If fuses burn out, check to see that the proper voltage has been supplied to the power input

module. If fuses burn out repeatedly call Duniway Stockroom.

Display Shows -LO, OFF or HI:

If the digital display consistently shows

-LO

OFF

, it

may be that one of the internal power supply protection devices has removed power to the CDG.

You may check this by measuring the voltage at the connector or cable for the unaffected gauge.

Since power for both gauges use the same protection device, either connector will show the power

supply voltages. Normal range for the voltages are 14.5 to 15.5 volts for both +15 volts and -

15 volts. +15 may be measured on the red wire; -15 is on the green wire; power return is on the

black wire. If the power supply protection has shut the power off, you will typically measure less

than 4 volts on the affected supply.

If you verify that either power supply is shut off, remove power from the CDG for a few minutes

to allow the protection device to reset itself. The protection device does not need to be replaced;

it is a reusable thermal fuse.

You may wish to determine the cause for the loss of power supply voltage before applying power

again. The 908A will protect itself if it finds excessive power draw again.

It is normal for the 908A to feel warm to touch along the left side of the case. This is especially

true when operating heated CDGs because of the greater power they require.

TELEPHONE: 650-969-8811 TOLL-FREE (U.S. only): 800-446-8811 FAX: 650-965-0764 EMAIL: [email protected]

www.duniway.com

Содержание Terranova 908A






























Результаты поиска

Содержание Terranova 908A

Отзывы:

Похожие инструкции для Terranova 908A

Бренды по названию

Популярные бренды

DUNIWAY Stockroom Terranova 908A, Инструкция по эксплуатации

Результаты поиска

Содержание Terranova 908A

Отзывы:

Похожие инструкции для Terranova 908A

Бренды по названию

Популярные бренды