Dundalk LeisureCraft Panoramic Barrel Sauna Скачать руководство пользователя страница 5

Страница: 5 / 48

Using 2 people, gently place the acrylic dome into the

groove at the back of the sauna.

l S

Dundalk LeisureCraft

Panoramic Barrel Sauna Assembly Instructions

ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com

Attach the stave supports using 2 ½” (64mm) screws

making sure they are flush with the curve of the cradle.

*These supports are temporary to assist in the

installation of the acrylic dome and will be removed

later in the assembly process .

Start laying down the wall staves. Keep the dado grooves

in line with the correctly positioned bottom stave.

Make sure there are no gaps between the edges of the

staves, and that the groove line for the dome is lined up

perfect.

Place the door section into the dado groove in the staves.

Make sure the door is centered with the middle stave.

Содержание Panoramic Barrel Sauna

















































Результаты поиска

Содержание Panoramic Barrel Sauna

Отзывы:

Похожие инструкции для Panoramic Barrel Sauna

Бренды по названию

Популярные бренды

Dundalk LeisureCraft Panoramic Barrel Sauna, Руководство по сборке

Результаты поиска

Содержание Panoramic Barrel Sauna

Отзывы:

Похожие инструкции для Panoramic Barrel Sauna

Бренды по названию

Популярные бренды