Duncan Enviro 740 Скачать руководство пользователя страница 29

Страница: 29 / 72

Pt. No. 67304

Issue 1217

Maintenance

Your new Duncan ‘Enviro’ Drill will give long and efficient
service if given normal care and maintained properly.

fig 32

Item Components

Lubricant

*Frequency

Wheel Bearings

Castrol LMX Grease

Annually

Gearbox

Castrol Hyspin AWH 32/68 Oil (1.25 Litres) Maintain Level

Wheel Arm Pivots

S.K.F. LGEM2 Grease or Equivalent

Weekly

Drive Chains

Suitable Roller Chain Lubricant

6 Monthly

Coulter Pivot Pins

S.K.F. LGEM2 Grease or Equivalent

Weekly

Front Disc Bearings

(Pre-packed & Sealed)

Not Required

Double Disc Bearings

(Pre-packed & Sealed)

Not Required

Drive Shafts (Side Frame)

(Pre-packed & Sealed)

Not Required

Agitator Shaft

Nylon Bushes

Not Required

Seeder Shafts

Nylon Supports

Not Required

The lubrication frequencies are only a guide. Actual frequency will be dependent on extent of use and ground conditions.

Components

Daily

Weekly

Pre

Season

(or after 20Ha)

(or after 100Ha)

(or 1000 Ha)

Coulters & Double Discs

•

Press Wheels

•

Seeders/Agitators/Bottom Flaps

•

Wheel Nuts

•

Pivot Pin Fasteners

•

Coupling & Safety Chains

•

Roller Chains

•

Gearbox/Clutch

•

Hydraulics (Oil Leaks)

•

Tyre Pressures (25psi / 1.8bar)

•

Bolted Connections

•

Precautions with Grease

Greases should not be mixed as the structure may be
weakened by the mixing of different types of thickener
which may cause softening and loss of grease from
bearings by running out.

Lubrication Chart

Maintenance Schedule

Содержание Enviro 740









































































Результаты поиска

Содержание Enviro 740

Отзывы:

Duncan Enviro 740, Руководство пользователя, Страница: 29 / 72

Результаты поиска

Содержание Enviro 740

Отзывы: