background image

25

Pt. No. 67304

Issue 1217

Farmscan Jackal v3 Settings Setup

Refer to the manual supplied with your Farmscan Jackal kit for information and operation.

Farmscan Jackal v3 Factory Setup for Enviro 740 

Refer to pages 6,9,11 of the Farmscan Jackal v3 manual. 

Input 2

 -Two wire ‘reed’ sensor for ‘Area/Speed Wheel’

measurement taken from shaft on drive pedestal.
The white ‘signal’ lead is connected to input A2.

Refer to the Farmscan manual if you want to make additional sensor connections.

It is advisable, as with all things electronic, to have a backup of your totals. We suggest you record 
these on a daily basis in a notebook or diary.

       

Input 2 Edit

 m/pulse
Auto Set:
Target:0.000m
Meas.pulses:  

0

Manual Ratio:
  2.817000

 NEXT

 

      

EDIT

       

Other Settings

Implement Width:
 x.xxx  m
Extern.Run/Hold:
Disabled

Alarm Beep:2

 NEXT

 

      

EDIT

A1

A2

A3

A4

A5

A6

A7

A8

A9

A10 A11

1 Gnd

A2 Signal

Connect to Pedestal Shaft
2 Wire Sensor via extension 
cable.

Connect directly
to Tractor Battery

+12v

0v

red

black

white

black

Machine 

Size

Row Spacing 

(mm)

Sowing Width 

(m)

15 Run

150

2.25

17 Run

130

2.21

19 Run

150

2.85

21 Run

135

2.84

23 Run

150

3.45

26 Run

130

3.38

Rolling Circumference of 12 ply Tyre = 3.708m 
See page 20 for directions on how to obtain
an accurate measurement for the tyre fitted
to your machine.
The ‘drive ratio’ is always 1.316

Manual Ratio

               = 

Circumference of Tyre

                                                Drive Ratio

                                    = 

3.708 m

                                              1.316

                                    =

 2.817m

Содержание Enviro 740









































































Отзывы: