Duncan Enviro 740 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 72

Duncan Enviro 740 Скачать руководство пользователя страница 12

10

SAFETY - Machine Specific
(Continued)

Hazard Points on the Duncan Enviro
(Continued)

Chain Guards & Access Covers

To prevent hands, etc. getting caught in the gearbox drive
chain, a guard is provided to cover sprockets, chain and chain
tensioner mounted on the side of the mainframe side plate.
A guard is also provided to cover the seedbox drive chains
at the rear of the gearbox. The metal access plates on the
side frames and the wheel legs must only be removed during
servicing. All these guards must be fitted while using the
machine.

Warning

: Access to pinch points is still possible from

underneath the machine.

For guard locations on machine, refer Page 11.

Calibrating

Be particularly careful when calibrating the seeding rate. At
this time, the calibration trays have been removed and are no
longer covering the rotating seeder units. See

Pinch Points/

Moving Parts

(Page 9) for hazardous areas.

Transport

The two large wheels located at the sides of the machine are
for the purpose of controlling maximum loading on dragbars
and coulters and gearbox input drive (RH wheel). These are
also used to support the machine weight during transport
(while linked to the tractor).

Important -

Refer to safety cautions in the

Transport

section,

Page 13 of the manual.

Ensure that all linkage pins and security clips are fitted
correctly.

Maintenance

Refer Page 26 - 30 for the

Care and Maintenance

section of

the manual.

Lubrication

Refer Page 27 for the

Lubrication

section of the manual.

«
...
10
11
12
13
14
...
»

Содержание Enviro 740









































































Отзывы:

Нет отзывов