Duluth Forge DF25SMS Скачать руководство пользователя страница 20

Страница: 20 / 32

www.factorybuysdirect.com

HSE-MAN-013

INSPECTING BURNERS

IMPORTANT: Owner’s should check pilot flame pattern and burner flame pattern often.

Incorrect flame patterns indicate the need for cleaning (see Care and Maintenance,

page 21 or service.

WARNING: Only a qualified service person should service and

repair heater. This includes maintenance requiring replacement or

alteration of components.

PILOT FLAME PATTERN

Figure 19 shows a correct pilot flame pattern.

Figure 20 shows an incorrect pilot flame pat-

tern. The incorrect pilot flame is not touching

the thermocouple. This will cause the ther-

mocouple to cool, which shuts the heater off.
If pilot flame pattern is incorrect, as shown

in Figure 20
• turn heater off (see

To Turn Off Gas to Ap-

pliance

, page 19 or 20)

• see

Troubleshooting

pages 22 through 26.

WARNING: If yellow tipping

occurs, your heater could pro-

duce increased levels of carbon

monoxide. If the burner flame

pattern shows yellow tipping,

follow instructions at bottom of

this page.

Notice:

Do not mistake orange flames with

yellow tipping. Dirt or other fine particles enter

the heater and burn causing brief patches of

orange flame.

Figure 19 - Correct Pilot Flame Pattern

(Natural Gas shown)

Figure 20 - Incorrect Pilot Flame Pattern

(Natural Gas shown)

3-3.5" WC

Natural Gas

Shown

8-11" WC

3-3.5" WC

Natural Gas

Shown

8-11" WC

Approx. 3"-6" Above Top of Logs

More Than 8" Above Top of Logs

Approx. 3"-6" Above Top of Logs

More Than 8" Above Top of Logs

Figure 21 - Correct Burner Flame Pattern

Figure 22 - Incorrect Burner Flame

Pattern

BURNER FLAME PATTERN

Figure 21 shows a correct burner flame pattern. Figure 22 shows an incorrect burner flame

pattern. If burner flame pattern is incorrect as shown in Figure 22:
• turn heater off (see

To Turn Off Gas to Appliance

, page 19 or 20).

• see

Troubleshooting

pages 22 through 26.

BURNER PRIMARY AIR HOLES

Air is drawn into the burner through the holes in the fitting at the entrance to the burner. These

holes may become blocked with dust or lint. Periodically inspect these holes for any blockage

and clean as necessary. Blocked air holes will create soot.

Содержание DF25SMS

































Результаты поиска

Содержание DF25SMS

Отзывы:

Похожие инструкции для DF25SMS

Бренды по названию

Популярные бренды

Duluth Forge DF25SMS, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание DF25SMS

Отзывы:

Похожие инструкции для DF25SMS

Бренды по названию

Популярные бренды