Duerkopp Adler 550-12-23 Скачать руководство пользователя страница 22

Страница: 22 / 23

4.9

Threading lower tape feed (550-12-26 only)

Caution Risk of Injury !

Before threading turn the main switch off.

Threading the tape

–

Put the roll in place.

–

Pass tape over clamping lever.

–

Place top in position.

–

Thread tape as shown in illustration.

–

Press key 3 once to release the tape clamp.

–

Thread tape into channel 1 as far as the tape cutter 2.

–

Press key 3 again to close the tape clamp and activate the

tape cutter.

–

Begin sewing.

Removing residual tape from tape channel in needle plate

–

Press key 3 once.

–

Push pedal forwards.

–

Remove residual tape with tweezers.

–

Press key 3 again.

Note:

When sewing with a programme, it will be impossible to activate the

key 3 for inserting the tape and for removing the tape remnant before

the pedal has been lowered backwards.

Содержание 550-12-23
























Результаты поиска

Содержание 550-12-23

Отзывы:

Похожие инструкции для 550-12-23

Бренды по названию

Популярные бренды

Duerkopp Adler 550-12-23, Руководство по эксплуатации

Результаты поиска

Содержание 550-12-23

Отзывы:

Похожие инструкции для 550-12-23

Бренды по названию

Популярные бренды