Duerkopp Adler 1220-6 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 35

Duerkopp Adler 1220-6 Скачать руководство пользователя страница 22

19

3.7.6 Replacement the indented belt

Before replacing the indented belt, the bottom feeding shaft

is to be removed. The procedure is as follows:

Caution! Danger of injury!

Switch off the main switch! Before starting the

setting operation, wait until the motor stops!

- Loosen the screw (1) of the tensioning roller (2) and loosen

it.

- Loosen the screws (3) of the pulley (4) and shift it to the left

in such a way that the screws (5 and 6) of the feeding clutch

(7) are accessible.

- Loosen the screws (5 and 6).

- Loosen the screws (8) of the axial rings (9).

- Push the shaft (12) to the left in such a way that it is out of

the pulley (4).

- Remove the pulley (4).

- Remove the front guard.

- Loosen and unscrew the screw (14) of the holder of the

wheel (15) and remove it from the holder (24).

- Loosen the screws (16 and 17) of the holder (18).

- Remove the holder (18) together with the holder (15) and

articulated shaft (13) from the machine.

- Loosen the screws (19) of the pulley (20).

- Remove the retaining ring (21) from the shaft (22).

- Hold the pulley (20) and pull out the feeding shaft (22) from

the arm in such a way that it is possible to remove the

indented belt (23) from the arm of the machine.

- Replace the belt with a new one and proceed to the assembly

(inverted procedure of dismantling).

- Proceed to the setting operation according to the par. 3.7.3,

3.7.4 and 3.7.5.

3.7.7 Setting the feeding difference

The size of feeding by the driven top roller is regulated by

means of a regulating screw. The top roller feeding is to be set

in cases, when a difference between the size of the top and

bottom feeding of the sewn material is evident. This will show

up in upward or downward bending of the sewn parts. It is

therefore necessary, when bending the sewn parts:

1. upwards - to increase the feeding performance of the top

roller.

2. downwards - to reduce the feeding performance of the top

roller.

This setting operation is done as follows:

- Loosen the locking nut (1) of the adjusting screw (2).

- Turn the screw to the left (in increasing so the feeding perfor-

mance of the top roller) or to the right (in reducing so the

feeding performance of the top roller).

- Test the result of this setting in sewing.

- Tighten the locking nut (1).

- The standard setting for the zero difference is 3 mm (see

Fig.) - the gap between the front faces of the screw (2) and

the nut (1).

1

4

12

8 9

3

2

5 6

7

24
15

14

21

22

23

20

19

13

17

18

16

2

1

3

9

«
...
20
21
22
23
24
...
»

Содержание 1220-6




































Отзывы:

Нет отзывов