Ducati HYPERMOTARD 950SP Скачать руководство пользователя страница 238

Страница: 238 / 295

Check clutch and brake fluid level

The levels should not fall below the MIN marks on

the respective reservoirs.

If level drops below the limit, air might get into the

circuit and affect the operation of the system

involved.

Brake and clutch fluid must be topped up and

changed at the intervals specified in the scheduled

maintenance table contained in the Warranty

Booklet; please contact a Ducati Dealer or

Authorised Service Centre.

CLUTCH SYSTEM

If the control lever has exceeding clearance and the

transmission snatches or jams as you try to engage a

gear, it means that there is air in the circuit. Contact

your Ducati Dealer or Authorised Service Centre to

have the system inspected and air drained out.

Attention

Clutch fluid level will increase as clutch plate

friction material wears down. Do not exceed the

specified level (3 mm - 0.12 in above the minimum

level).

BRAKE SYSTEM

If you find exceeding clearance on brake lever or

pedal and brake pads are still in good condition,

contact your Ducati Dealer or authorised Service

Centre to have the system inspected and any air

drained out of the circuit.

Fig 196

237

Содержание HYPERMOTARD 950SP








































































































































































































































































































Результаты поиска

Содержание HYPERMOTARD 950SP

Отзывы:

Бренды по названию

Популярные бренды

Ducati HYPERMOTARD 950SP, Руководство пользователя

Результаты поиска

Содержание HYPERMOTARD 950SP

Отзывы:

Бренды по названию

Популярные бренды