Ducati HYPERMOTARD 950SP Скачать руководство пользователя страница 232

Страница: 232 / 295

Refuelling

Never overfill the tank when refuelling. Fuel should

never be touching the rim of filler recess (1).

Attention

Use fuel with low lead content and an original

octane number of at least 95.

Attention

The motorcycle is only compatible with fuel

having a maximum content of ethanol of 10% (E10).

Using fuel with ethanol content over 10% is

forbidden. Using it could result in severe damage of

the engine and motorcycle components. Using fuel

with ethanol content over 10% will make the

warranty null and void.

Fig 187

Max level

Fig 188

231

Содержание HYPERMOTARD 950SP








































































































































































































































































































Результаты поиска

Содержание HYPERMOTARD 950SP

Отзывы:

Бренды по названию

Популярные бренды

Ducati HYPERMOTARD 950SP, Руководство пользователя

Результаты поиска

Содержание HYPERMOTARD 950SP

Отзывы:

Бренды по названию

Популярные бренды