+
12V/OUT
_
CN5
CN6
-
LED-POW
LED--6
LED
LED--5
PANIC ALARM SWTICH
PCB
LED
LED--6
LED
PT
2272-
M4
LED--POW
LED--5
DIP
8
7
6
5
4
ON
LED--4
3
2
1
PIC16C57C
MICROCHIP
LED
LED--3
LED--2
LED--1
DIP SWTICH
LED--4
LED--1
LED--3
LED--2
TAMPER SWITCH
BATTERY CONTAINER
+-
R
T
0
302
ALARM/OUT
GND
-
+
SONLE
SRS-12VDC-SL
+
_
12V/IN
+
RELAY
CN5
CN6
_
12V/OUT
+
RELAY
ALARM/OUT
+
12V/IN
_
BUZZER
CONNECTION COLUMN
BOTTOM COVER
1
2
3
4
5
6
7
8
9
10
11
12
_
+
7. panic alarm:
when danger occur in your home, you can prees the panic key to give panic asking for help
signal to neighbor or others and obtain other’s help.
8. alarm memory:
on fortify state, when host isn’t at home there is person enter detection field, general controller
alarm, after the alarm stops, the corresponding LED still light to indicate that channel ever had danger, only after
using remote controller to reset, the LED will be off.
GENERAL CONTROLLER
1
．
Connection-wire figure:
1.1. terminal 1&2: output voltage, connect 1
with “-“,connect 2 with “+“;
1.2.
terminal 3&4 can connect with wire
detector, is 5
th
channel CN5,
corresponding indicator is Ch5;
1.3.
terminal 5&6 can connect with wire
detector, is 6
th
channel CN6,
corresponding indicator is Ch6;
1.4. terminal 7&8: alarm output, when it alarm,
other alarm connected with it also
alarm,7connect with “-“, 8 with “+”;
1.5. terminal 9&10: other output;
1.6. terminal 11&12 input voltage , connect 11
with “-“, connect 12 with “+“.
2
．
operation
2.1 install detector on selected position;
2.2 connect wire according to connection-wire
figure: connect “-” and “+” of power adapter to
terminal 11&12, and the polarity can not be
connected oppositely, connect CN5 and CN6 with
wire detector, they are two wire channels, the
correspondinng indicator separately is Ch5 and Ch6,
NOTE: if CN5 or CN6 is not connected, general controller
will alarm and corresponding channel LED (Ch5 or Ch6) will light, so when no wire detector connected, CN5
and CN6 shoud be short connected avoiding unwanted alarm;
2.3 install 6 AA batteries into battery container according to right polarity;
2.4 plug power adapter into power socket, power LED should light, Fortify and Low-battery LEDs flash once 0.5
second, after 60s, general controller give one DI sound, Fortify LED flashes once 2s and Low-batter4y LED stop
flashing and remain on.
NOTE: during this 60s, any operation is not effect.
2.5
close front cover.
NOTE: after power is on, there is 60s to wait you close front cover avoiding tamper
alarm.
2.6 press the panic key on general controller, it give panic alarm and all LEDs light, the alarm time is 3Min 30s(press
the cancel key on 4-key remote controller to stop alarming quickly);
2.7 press fortify key on 4-key remote controller, set general controller on fortify state;
2.8 test every detector one by one, when wire detector work, general controller alarm, the alarm time is 3Min 30s,
the corresponding channel LED
（
Ch5 or Ch6
）
should light. When wireless detector work, general controller
should alarm, alarm time is 3Min 30s, corresponding channel LED
（
Ch1 or Ch2
，
3
，
4
，
5
，
6
）
should light.
3. attention:
avoid installing the unit on metal base;
when general controller alarming, the sound is very high, so when alarm occur, you should eliminate it in
time avoiding affecting others.
if power adapter need replacing, the replacing adapter’s standard should be: input voltage
110VAC/230VAC, output voltage 10~12V/DC, current 1A. suggest you contacts with supplier and use original
adapter.
if the power adapter is connected oppositely, the unit will not work, but it will not be damaged;
