background image

12

Programming Descriptions

.

NOTE: 

A relay may be required for proper operation in other configurations. 

See paragraph 3.3 Terminal Connections.

Option 1 - Low battery

All Modes

If the battery voltage drops below 5.72V

DC

 a trouble will be indicated until the

battery voltage rises to 5.87V

DC.     

Default -

 ON

Option 2 - Input Supply Failure

All Modes

If AC power is absent or if DC power drops below 8.8V

DC  

on the RED and BLK

terminals, this

 

trouble is indicated. Default

 -

 ON

Option 3 - Zone Fault/Tamper (DEOL Only)

Modes 2, 3

A trouble will be indicated if any zone reports a fault or tamper condition. In Sec-
tion [11], Option [2] must be set to 

OFF 

and Option [3] must be set to 

ON

 for this

option to be enabled.    

Default -

 OFF

Option 4 - No Service Available

All Modes

This trouble is indicated If the system is unable to detect cellular service.

Default -

 ON

Option 5 - Radio Failure

All Modes

This trouble is indicated if there is an internal fault with the cellular radio.

Default -

 ON

Option 6 - PC5108 Failure

Mode 3

This trouble is indicated if a PC5108 supervisory or Keybus fault occurs. 

NOTE: 

The PC5108 tamper is communicated only, therefore it can only be

enabled by turning on section 20 option 7 and section 21 option 5.  There is no
local annunciation for this event.    

Default -

 ON

Option 7 -  Failure to Communicate (FTC)

All Modes

This trouble will be indicated if no acknowledgement has been received from

Connect 24

 after three attempts.    

Default -

 ON

Option 8 - Skyroute CL3050 Tamper

All Modes

This trouble will be indicated if the cover is removed from the Skyroute CL3050
activating the on-board tamper switch.    

Default -

 OFF

[15] System Time

All Modes

When the time and day have been programmed, the values are saved and are
used as the current time and day whenever the Skyroute CL3050 does a power
up. Time and day programming is only required if the installer desires the Sky-
route CL3050 to test transmit at a specific time and/or day.  There is no "loss of
time" trouble on the Skyroute CL3050.

Default -

 0000 - 2359

Zx

COM

Control Panel

RED    BLK YEL  GRN  COM  PGM

5.6K

Skyroute CL3050

Содержание Skyroute CL3050 ver 1.2





























Отзывы: