DSC PDigital Security PC1565, Руководство по установке, Страница: 18 / 56

127( ,IDVHFRQG)LUHW\SH]RQHLVYLRODWHGRULIWKH)LUHNH\V
DUH SUHVVHG GXULQJ WKH GHOD\ SHULRG WKH SDQHO ZLOO ODWFK WKH
DODUPRXWSXWDQGZLOOLPPHGLDWHO\FRPPXQLFDWHWKHDODUP
A violated Fire zone will be displayed on all keypads and can
be delayed at any keypad. Typically this zone is used for
latching smoke detectors.
>@6RXU)LUH=RQH
127(
'RQRWZLUH)LUH]RQHVRQNH\SDG]RQHWHUPLQDOVLIWKH
'(2/ VXSHUYLVLRQ RSWLRQ LV HQDEOHG IRU WKH SDQHO VHFWLRQ
>@RSWLRQ>@
When this zone is violated, the panel will immediately latch the
alarm output and communicate to the central station. The
alarm will sound until the Bell Cutoff time expires, or until a
code is entered (see section 5.13
“Bell” on page 21).
A violated Fire zone will be displayed on all keypads. Typically
this zone is used for pull stations.
>@+RXU6XSHUYLVRU\=RQH
If this zone is violated when the system is either armed or dis-
armed, the panel will report to the central station, and will log
the zone alarm to the Event Buffer. This zone gives a silent
alarm by default.
127( 'R QRW ZLUH +RXU 6XSHUYLVRU\ ]RQHV RQ NH\SDG
]RQHWHUPLQDOV
>@+RXU6XSHUYLVRU\%X]]HU=RQH
If this zone is violated when the system is either armed or dis-
armed, the panel will immediately latch the keypad buzzer
until a valid access code is entered and will immediately com-
municate to the central station.
>@+RXU%XUJODU\=RQH
If this zone is violated when the system is either armed or dis-
armed, the panel will immediately latch the alarm output and
communicate to the central station. The alarm will sound until
the Bell Cutoff time expires, or until a code is entered (see
section 5.13
“Bell” on page 21).
>@>@
The following zone definitions operate similar to the 24 Hour
Burglary except for the System Event output type and the SIA
identifier:
>@+RXU+ROGXS=RQH
- This zone gives a silent alarm by
default.
>@+RXU*DV=RQH
>@+RXU+HDW=RQH
>@+RXU0HGLFDO=RQH
>@+RXU3DQLF=RQH
>@+RXU1RQ0HGLFDO(PHUJHQF\=RQH
>@+RXU6SULQNOHU=RQH
>@+RXU:DWHU)ORZ=RQH
>@+RXU)UHH]HU=RQH
>@+RXU/DWFKLQJ7DPSHU
If this zone is violated, the installer must enter Installer’s Pro-
gramming before the system can be armed.
127( :LUHOHVV ]RQHV VKRXOG QRW EH SURJUDPPHG DV ]RQH
W\SHV>@>@
>@0RPHQWDU\.H\VZLWFK$UP=RQH
Momentary violation of this zone will alternately arm/disarm
the system. Tampers and faults will not arm/disarm the sys-
tem, but only activate the appropriate trouble.
>@0DLQWDLQHG.H\VZLWFK$UP=RQH
When this zone is violated, the system will arm. When this
zone is secured, the system will disarm. Tampers and faults
will not arm/disarm the system, but only activate the appropri-
ate trouble.
>@)RU)XWXUH8VH
>@,QWHULRU'HOD\=RQH
This zone type is normally used with motion detectors and has
a standard exit delay time.
If the panel is Away armed (a delay zone is violated during the
exit delay, or the Away function key is used), the Interior Delay
zone will work the same as the Interior zone [04].
If the panel is Stay armed (a delay zone is NOT violated dur-
ing the exit delay, the Stay key is used, or [*][9] is used for
arming), a violation of the zone will initiate Entry Delay 1.
>@3XVKWR6HW=RQH
If any zones are programmed as Push to Set, when the system
is armed, the panel will suppress all audible exit delay beeps/
squawks and begin an infinite silent exit delay. When a user
violates and restores a Push to Set zone, the panel will wait 5
seconds, then terminate the Exit Delay and arm the system.
127( 'RQRWHQDEOH([LW'HOD\7HUPLQDWLRQLIWKLV]RQHW\SH
LVXVHGVHH
“Entry/Exit Delay Options”
RQSDJH'R
QRWFKDQJHWKHDWWULEXWHVRI3XVKWR6HW]RQHVIURPWKHGHIDXOW
VHWWLQJV
>@+RXU%HOO%X]]HU=RQH
This zone works like a 24-Hour Burglary zone (zone type [11])
while armed, and a 24-Hour Supervisory Buzzer zone (zone
type [10]) while disarmed. When the panel is armed and this
zone is violated, the bell sounds until the bell time-out timer
expires. When the panel is disarmed and this zone is violated,
the keypad buzzers sound until a user enters an access code.
>@'HOD\HG+RXU)LUH:LUHOHVV
This zone type operates the same as [07] Delayed 24 Hour
Fire Zone and must be used if the smoke detector is wireless.
>@6RXU)LUH:LUHOHVV
This zone type operates the same as [08] Standard 24 Hour
Fire Zone and must be used if the smoke detector is wireless.
Zone Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [001]
Zone Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [202]
5.3 Zone Attributes
127( $OO]RQHVZLWKWKHH[FHRXUDQG)LUHZLOO
SURYLGHDQH[LWGHOD\
127( 'RQRWFKDQJHWKHDWWULEXWHVIRU)LUH=RQHVIURPWKH
GHIDXOWVHWWLQJV
Additional zone attributes can be programmed to customize
the operation of a zone for a specific application. The follow-
ing attributes are programmable for each zone:
•
$XGLEOH 6LOHQW±
This attribute determines whether or
not the zone will activate the alarm output.
•
3XOVHG6WHDG\±
This attribute determines whether the
alarm output will be steady or will pulse on and off every
second.
•
$FWLYDWH &KLPH ±
This attribute determines whether or
not the zone will activate the chime feature (see “[*][4]
Door Chime On/Off” on page 8).
•
%\SDVV (QDEOH ±
This attribute determines whether or
not the zone can be manually bypassed (see “[*][1]
Bypassing and Activating Stay/Away Zones” on page 7).